User manual STRONG SRT 8410

[. . . ] Digital Terrestrial Receiver with Embedded Viaccess SRT 8410 User manual Safety Instructions SAFETY INSTRUCTIONS Grounding, Polarization -- If this product is used with a specified AC adapter, the adaptermay be equipped with a polarized alternating current line plug (a plug with one blade wider than the other). This safety feature allows the plug to fit into the power outlet only one way. If you cannot insert the plug into the wall outlet, pull it out, reverse it, and then reinsert it. If the plug still fails to fit, contact an electrician and have the receptacle replaced n Protecting the Power Cord -- The power supply cord should be placed so it will not bewalked on. [. . . ] Use a cloth lightly dampened with water (no solvents) to clean the exterior. Never store the receiver where it is exposed to direct sunlight or near heating equipment e. g. ATTACHMENTS: Do not use any attachment that is not recommended by the manufacturer; it may cause a hazard or damage the equipment. CONNECTION: Connect all components before plugging any power cords into the wall outlet. Always turn off the receiver, TV and other components before you connect or disconnect any cables. LIGHTNING: If the receiver is installed in an area subject to intense lightning activity, protection devices for the receiver mains connector and modem telephone line are essential. The individual manufacturer's instruction for safeguarding other equipment, such as TV set, Hi-Fi, etc. , connected to the receiver must also be followed during lightning storms. NOTE: Dispose the used batteries at designated place for environment protection 5 2. 0 INTRODUCTION 2. 1 Front Panel 1. TO TV If you want your antenna signals from "ANT IN" connector inject to second receiver or TV set. Use this loop trough output "TO TV" to connect these by using a coaxial cable. HDMI Use this connection to connect the receiver to your TV using HDMI cable. S/PDIF Digital audio output Use this coaxial output to connect your receiver to the input of your digital audio amplifier. AUDIO Right (Red RCA) and Left (White RCA) These connectors give you the possibility to connect the audio signal to an external amplifier or to the audio input of your TV. TV SCART Connector Use this connector to connect your receiver with your TV set using a SCART cable. Main power switch 2. 3 Remote control Remove the battery compartment cover and load two AAA (UM-4 or R03) batteries. Make sure that the batteries have been inserted in the correct polarities matching to the symbols +, - marked in the battery compartment. Do not mix new and used batteries otherwise the operation lifetime will be much shorter than normal. Remove the batteries if the unit will not be used for a prolonged period of time. Be sure to aim the remote control directly at the infrared sensor of the unit during operation. The sensor may not able to receive the remote signal when it is exposed to direct sunlight or a strong artificial light (fluorescent or strobe light). In this case, change the direction of the light or reposition the unit to avoid direct lighting. BE ENVIRONMENTALLY FRIENDLY Do not dispose batteries as normal rubbish. [. . . ] You can read the present program information by pressing the i button on the remote control. Press EXIT to return. 6. 10 Switching between DTV and Radio mode You can switch between Digital TV mode and Radio mode by pressing "TV/RAD" button on your remote. 14 7. 0 SPECIFICATION Demodulator Modulation: Frequency range : Channel bandwidth: MPEG Video Decoder Standards: Formats: Aspect ratio: Video Scaling: OSD Colours: Resolution: Overlay: MPEG Audio Decoder Standard : DVB-T COFDM 174 ~ 234 MHz (VHF III) 470 ~ 862 MHz (UHF IV/V) 7/8 MHz switchable bandwidth ISO13818-2 (MPEG-2) ­ MP@ML, MP@HL ISO14496-10 MPEG-4 AVC MP@L3, HP@L4 576i25 (SD), 576p50, 720p50 (HD), 1080i25 (HD) 4 :3, 16 :9, Pan & Scan, Letter Box Variable 16/256 colours 2 ­ 16 bits per pixel MPEG stills/live image insertion ISO 11172-3 / ISO 13818-3 (MPEG) ISO14496-3 MPEG-4 AAC ­ LC/HE Dolby Digital (AC3) Decompression MPEG layers 1, 2 (Mono, Dual Channel, Joint Stereo, Stereo) HE-AAC (profile v1) level 4 decoding S/PDIF and HDMI audio output formats: PCM (decompressed stereo) Compressed Dolby Digital 5. 1 pass-through DTS with transcoded multichannel HE-AAC System resources Processor: RAM (system): ST7101 64 MBytes Loader Full code software download mechanism Authentication of downloaded material Front panel 3 digits 7 segments red display. 3 LEDs with backlighted symbols 3 buttons; Smartcard slot 15 Software & Features Access control: Setup menu: EPG: Languages: Viaccess ACS3. 0 Automatic channel installation, diagnosis, decoder configuration, parental control 7 days of EPG, if available from distributor multilingual OSD, audio and signaling supported Teletext processing EN 300 472 teletext re-insertion in the composite video signal EN 300 472 & EN 300 743 teletext and subtitling decoding Interfaces Mains input connector: ANT input: TO TV: 1 Scart: Analogue Audio: Digital Audio: Digital Video/Audio: Smartcard reader: General data Mains voltage: Power consumption: Typical consumption: Power consumption in standby: Operating temperature: Product dimensions: Weight: Detachable lead IEC-type, female IEC-type, male (loop-through) TV with RGB 2 RCA Stereo audio outputs (left and right) S/PDIF audio electrical output HDMI 1. 2A with HDCP copy protection 1 slot, ISO 7816 1, 2 & 3 96 ~ 264 V, 48/62 Hz max 10 W 8. 5 W in SD / 9. 5 W in HD max 0. 5 W +10 ~ 40 °C 280 x 200 x 35 mm 1. 2 kg Subject to alterations. [. . . ]