User manual STRONG SRT 8345 CI

[. . . ] Digital High Definition Satellite and Terrestrial Receiver SRT 8345 CI User Manual Picture similar PART 1 · English TABLE OF CONTENTS 1. 0 INTRODUCTION 1. 1 Safety Instructions 1. 2 Storage 1. 3 Equipment Set-up 1. 4 Features & Accessories 2. 0 YOUR RECEIVER 2. 1 Front Panel 2. 2 Rear Panel 2. 3 Remote Control Unit 3. 0 CONNECTIONS 3. 1 Connecting to a Satellite Dish 3. 2 Connecting to Terrestrial antenna 3. 3 Connecting to TV & VCR 3. 4 Download new software 3. 5 Connecting to external USB Hard disk 4. 0 STARTING UP FOR THE FIRST TIME 4. 1 Language Selection 4. 2 Select Satellite 4. 3 Dish adjustment 4. 4 Channel set-up 4. 5 Digital Terrestrial TV installation 5. 0 MAIN MENU 5. 1 Channel Organizer 5. 2 Satellite Search 5. 3 Terrestrial Search 5. 4 Installation 5. 5 Timer 5. 6 Application 5. 7 Common Interface 6. 0 OTHER OPERATIONS 6. 1 Program Guide (EPG) 6. 2 Zapping and information banners 6. 3 Channel list and view mode 6. 4 PDR functions A. 1 TROUBLESHOOTING A. 2 SPECIFICATIONS 2 2 3 3 4 5 5 6 7 9 9 10 10 11 11 11 12 12 12 12 12 13 13 15 19 19 22 22 23 24 24 24 24 25 27 27 1 English PART 1 · English 1. 0 INTRODUCTION 1. 1 Safety Instructions The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of not isolated dangerous voltage with the inside of the product that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance. Read All Instructions - Before you use the product, read all operation instructions, For more information on accessories such as the lithium ion battery, refer to the manuals provided with those products. Save These Instructions- Save all safety and operating instructions for future reference. [. . . ] You can select transponder in order to check signal strength and quality of reception. If you need to modify transponder list please use menu Edit satellites as described in chapter 5. 2. 3. If you need to scan specific transponder then use Manual scan as described in this chapter below. 15 English PART 1 · English Network search: if this item is set to "No" then receiver will search for the channels that are available from preset transponder list of selected satellite. If this item is set to "Yes" then receiver in addition will search for the channels from transponders information about that can be found from broadcast. Search for: you can select type of the channels that will be installed to your receiver. If selected All channels then receiver will install Free-To-Air and Scrambled channels If selected Scrambled then receiver will install only Scrambled channels If selected FTA then receiver will install only Free-To-Air channels Once you complete all settings you can start channel search process. Press RED button to install channels from all transponders of the satellite; Press GREEN button to install channels from transponder selected in Transponder item; Press YELLOW button to enter to Manual setup channels from specific transponder or to setup single channel with known Video and Audio PID. n n Manual setup of channels In Manual channel search menu you can setup all channels from specific transponder or single channel. To setup all channels from specific transponder: n Satellite: indicate name of the satellite where channels will be searched n Frequency: Use Numeric buttons to enter frequency of transponder n Polarisation control: Use tu buttons to select polarisation of transponder n Symbol rate: Use Numeric buttons to enter symbol rate value n Network search: Use tu buttons to select ON or OFF n Search for: Use tu buttons to select type of channels to be installed Press RED (Search) To setup single channel from specific transponder: To use this function you need to know special values that identify single channel. For this reason you may need to consult to special magazines or internet. n It is necessary to setup all parameters of transponder as described in above. n Satellite: indicate name of the satellite where channels will be searched n Frequency: indicate frequency of transponder where you install channel n Service ID: Use Numeric buttons to enter value in decimal n Video PID: Use Numeric buttons to enter value in decimal n Audio PID: Use Numeric buttons to enter value in decimal n CAS: Use tu buttons to select ON or OFF. Set to ON if channel is encrypted, otherwise keep OFF n HD Video: Use tu buttons to select ON or OFF. Set to ON if channel is HD, otherwise keep OFF n AC3 Audio: Use tu buttons to select ON or OFF. Set to ON if channel has AC3 audio and you are going to use AC3 audio, otherwise keep OFF 16 PART 1 · English To add channel press YELLOW (Save) or BLUE (Save&Exit) button. The new channel will be added to the list with name "Video CH XXXX", where XXXX is equal to PCR PID (Video) you have entered. 5. 2. 1. 1 Positioner setup If in Dish setup menu you have configured Dish mode as "DiSEqC 1. 2" then you have to setup position of the dish to each satellite that you want to install. In Channel setup menu move menu focus to Dish position item and press OK button on remote control. n Satellite: Displays the name of satellite position of antenna for which you setup n Transponder: Use tu buttons to select reference transponder, receivable in your location, to measure signal strength and quality n Movement speed: Use tu buttons to select between Slow and Fast. Slow speed allows you to fine adjust position of the dish (each press to direction button will turn dish to short angle). If Movement speed set to Fast press to direction button will couse continuous movement of the dish to appropriated direction, to stop dish you will have to press OK button. n Move: Use tu buttons to move dish to the East/West direction n Centre position: If you press OK button while menu focus is on this item then dish will be turned to centre position, which corresponds to true South direction. n Limits: Use tu buttons to Enable or Disable software limits of your positioner. [. . . ] Select with the pq buttons the file you want to watch and start playback by pressing OK. You can activate Fast Forward or Fast Rewind during playback by pressing the 7 or 8 button. Another pressing of these buttons will change the speed (FF: x2, x4, x8; FR: x1, x2, x4, x8). Press Ñ (Play) button to continue playback at desired position. [. . . ]