User manual STRONG SRT 8200

[. . . ] Prijemnik za Digitalnu Zemaljsku Televiziju u HD Rezoluciji SRT 8200 Uputstvo za upotrebu User manual 400 kanala Ručno/ Auto. TV Info Pretraživanje favorit liste 4 Digitalni zvuk 30 Tajmera Natpisi MP3/JPG MPEG 0. 70 W Potrošnja Picture similar Table of content 1. 0 INTRODUCTION 1. 1 Safety Instructions 1. 2 Storage 1. 3 Equipment Set-up 1. 4 Accessories 1. 5 Usage of external USB devices 2. 0 Your receiver 2. 1 Front panel 2. 2 Rear panel 2. 3 Remote control 2. 4 Installing the batteries 2. 5 Using the remote control 3. 0 Connections 3. 1 Connecting to your aerial antenna 3. 2 Connecting to TV with HDMI cable 3. 3 Connecting to TV with a cinch cable 3. 4 Connecting to a digital audio amplifier 3. 5 Connecting to a digital A/V receiver and TV using HDMI 3. 6 Connecting an external USB storage device 4. 0 Starting up for the first time 4. 1 Antenna Adjustment 5. 0 Quick guide to using your receiver 5. 1 Changing channels 5. 2 Adjusting volume and audio 5. 3 Info Banner 5. 4 Electronic TV Programme Guide (EPG) 5. 5 Selecting the subtitle language 5. 6 Displaying Teletext 5. 7 Using external USB storage devices 6. 0 Main Menu 6. 1 Programme Organizer 6. 2 Channel search 6. 3 System Setup 6. 4 Tools 6. 5 Multimedia 7. 0 Troubleshooting 8. 0 Technical specification 9. 0 Appendix 2 2 2 2 3 3 3 3 3 4 4 5 5 5 5 5 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 11 13 15 16 18 19 22 Jun 2012 20:08 STRONG declares that this item complies with the basic requirements and other relevant regulations of directives CE 2004/108/EC and 73/23/EC, RoHS 2002/95/EC Subject to alterations. In consequence of continuous research and development technical specifications, design and appearance of products may change. All other product names are trademarks or registered trademarks of their respective owners. All rights reserved. 1 English 1. 0 INTRODUCTION 1. 1 Safety Instructions DO NOT INSTALL YOUR RECEIVER „„ a closed or poorly ventilated cabinet; directly on top of or under any other equipment; on a In surface which might obstruct the ventilation slots. [. . . ] Select the group to which the channel should be added with p/q and press OK. Additionally you can also select another favourite group where to add this channel. When you have added this channel to the desired group(s), press EXIT to go back to the channel list. There you can proceed like this to add other channels to favourite groups. You can also remove a channel from a favourite group by pressing the FAV button again and selecting the group it is part of. Then press OK to remove the symbol and the channel will be removed from this (these) favourite group(s). 6. 1. 2 Channel Sort This menu allows you to sort channels by the following methods: By LCN: The channels will be sorted according to the LCN (Logical Channel Numbering) system, which may be broadcasted in your area. If the operator doesn’t support LCN your channel numbers will start by channel number 800, otherwise the LCN channels will be sorted in regional order starting with 1. Further the LCN method will allow you to save the strongest channels broadcasted in your area, only. The channels will be sorted in ascending order of the frequency on which they By Frequency: are broadcasted. By Operator: The channels will be sorted by the operator ID. 6. 1. 3 Delete All Use this menu carefully!To execute this function it will be requested to enter the PIN code (DEFAULT PIN: 0000). After you have performed this action you will be guided to the Installation Guide again!Warning: The Delete all function will permanently delete all of the stored channels and settings from your receiver! 6. 2 Channel search Within the menu Channel Search you can adjust your search settings and perform an automatic or manual channel search. You will see the following submenus displayed: Search Setup, Auto Search and Manual Search. 6. 2. 1 Search Setup In the menu Search setup you can set the Antenna Power and the country in which you live. an active indoor/outdoor antenna) and it requires a voltage of 5 V and doesn’t consume more than 50 mA, then you can set the Antenna power to On. If you use an antenna without an amplifier or your antenna is already amplified by an external power supply or if you are using an antenna from a house distribution system, please keep Antenna power Off. 10 6. 2. 2 Auto Search After selecting this menu and pressing OK you will be asked to enter the PIN code (DEFAULT PIN: 0000) in order to update the current channel list. If you don’t want to perform a full channel scan you can press EXIT to cancel. After entering the PIN code (DEFAULT PIN: 0000) the receiver will perform an automatic channel search through all frequencies and after finishing this process it will update the channel list. During the search process the receiver will display the progress bar, the currently scanned frequency and the channel names. [. . . ] Use t/u to change and p/q to select, in order to set your preferred colour, background and font colour. 6. 5. 6 Remove USB device This menu item only appears if a USB device is connected. Select the menu item and press OK to safely remove the USB device from your receiver. Now you can disconnect the USB device after the message USB device is removed disappears. [. . . ]