User manual STRONG SRT 7300 CI

[. . . ] Digital High Definition Satellite Receiver SRT 7300 CI+ User Manual Bedienungsanleitung Gebruiksaanwijzing Manuel de l'utilisateur Manuale per l'uso Használati utasítás Návod k obsluze Používateľská príručka Picture similar 1 3 Fig. 2 2 3 5 6 8 1 2 3 4 6 9 9 11 13 15 16 18 19 22 23 26 28 17 21 20 25 24 29 27 5 7 8 10 8 12 14 Fig. 6 B A C PART 1 • English Table of Contents 1. 0 INTRODUCTION 1. 1 Safety Instructions 1. 2 Storage 1. 3 Equipment Set-up 1. 4 Accessories 1. 5 Usage of external USB devices 2. 0 Your Receiver 2. 1 DEFAULT PIN-CODE: 0000 2. 2 Front Panel 2. 3 Rear Panel 2. 4 Remote Control Unit 3. 0 Connections 3. 1 Basic connection using a Scart cable 3. 2 Basic connection using an HDMI cable 3. 3 Connecting multiple fixed dishes using a DiSEqC 1. 0 switch 3. 4 Connecting and using the IR extender 4. 0 Starting up for the first time 4. 1 Language selection 4. 2 System Setup 4. 3 Satellite Selection 4. 4 Scan Mode 4. 5 Signal Adjust 4. 6 Channel Setup 5. 0 Quick guide to using your receiver 6. 0 Operation 6. 1 Changing channels 6. 2 Info Banner 6. 3 Selection of audio language 6. 4 Teletext 6. 5 Subtitles 6. 6 Changing the video format 6. 7 EPG (Electronic Programme Guide) 6. 8 Instant Recording 6. 9 Timeshift 7. 0 Main Menu 7. 1 Installation 7. 2 Setup 7. 3 Channel 7. 4 Advanced 7. 5 Games 8. 0 TROUBLESHOOTING 9. 0 SPECIFICATIONS STRONG declares that this item complies with the basic requirements and other relevant regulations of directives 2004/108/EC and 73/23/EC, RoHS 2002/95/EC Subject to alterations. In consequence of continuous research and development technical specifications, design and appearance of products may change. [. . . ] All newly found channels will be stored at the end of the channel list. Note:  Press YELLOW in the Manual Scan menu to make settings for a PID search. Scan mode, Service type and Network search will then be replaced by settings for Video PID, Audio PID and PCR PID. For information on PID values, please visit websites like: www. lyngsat. com or www. kingofsat. net 7. 1. 4 Satellite Edit Here you can edit transponder data or add a new satellite. On the left of the screen, a list with all available satellites is displayed. The right of the screen displays a list will all available transponders for the highlighted satellite. Adding or editing a transponder Use pq to highlight the desired satellite. Press YELLOW to add a transponder or use pq to highlight the transponder to be edited and then press BLUE to enter the edit screen. Use pq to navigate in the edit screen and use tu respectively [0~9] to change the settings. Once all settings are made, press GREEN to save or EXIT to quit without saving. Editing an existing satellite Use pq to highlight the satellite you wish to edit. To edit the name of the satellite, use pq to highlight the name and press OK. Once finished press GREEN to save the changes or EXIT to quit without saving. To edit the position of the satellite, use pq to move the highlight to Position and use the [0~9] buttons to input the new position. To change the location, use pq to 11 English PART 1 • English highlight Location and use tu to change the location. Once all settings are made press GREEN to save or EXIT to quit without saving. Adding a satellite To add a satellite, make sure the highlight is not in the transponders list (press t in case of doubt) and press YELLOW. The procedure for adding a satellite is the same as for editing a satellite. 7. 2 Setup Use the Setup menu to configure the system settings of your receiver. The following sub-menus are available: Language, Output Options, Time Setting, Parental Control and OSD Display. 7. 2. 1 Language Here you can set the preferred Display, Audio and Subtitle languages and Country setting. Use pq to highlight the setting you wish to change and tu to change the value of the highlighted setting. Press OK for a list with all available options for the chosen setting. [. . . ] Doing so might cause irreparable damage to your receiver and will void your warranty. English 17 PART 1 • English 7. 4. 5 Factory Reset A factory reset will restore your receiver to the factory default settings. To reset the receiver, you have to enter your PIN code (Default PIN:0000). Warning:  factory reset will permanently delete all your personal settings, timers and stored A channels. [. . . ]