User manual STRONG SRT 7002

[. . . ] Digital High Definition Satellite Receiver SRT 7002 User Manual Bedienungsanleitung Manuel de l'utilisateur Manuale per l'uso Használati útmutató Руководство пользователя 03 Sep 2012 15:24 Picture similar 1 2 3 4 5 6 7 PART 1 • English English Table of Contents 1. 0 Instruction 2 1. 1 Safety Instructions 2 1. 2 Storage 2 1. 3 Equipment Set-up 3 1. 4 Accessories 3 1. 5 Usage of external USB devices 3 2. 0 Your Receiver 3 2. 1 PIN code default: 0000 3 2. 2 Front panel 3 2. 3 Rear panel 4 2. 4 Remote Control 4 2. 5 Installing the Batteries 5 2. 6 Using the Remote Control 6 3. 0 Connections 6 3. 1 Basic connection using a Scart cable6 3. 2 Basic connection using an HDMI cable 6 3. 3 Connecting multiple fixed LNBs using a DiSEqC 1. 0 switch 6 4. 0 First Time Installation 7 4. 1 Installation 7 5. 0 Quick guide for using your receiver 7 6. 0 Operation 8 6. 1 Changing channels 8 6. 2 Info Banner 9 6. 3 Selection of audio language 9 6. 4 Teletext 9 6. 5 Subtitles 9 6. 6 Changing the Aspect Ratio 9 6. 7 Changing the resolution 9 6. 8 EPG (Electronic Programme Guide) 9 6. 9 Favourite channels 10 6. 10 Changing between DTV/ VCR contents 10 7. 0 Main Menu 7. 1 Programme 7. 2 Picture 7. 3 Channel Search 7. 4 Time and date settings 7. 5 Option 7. 6 System Settings 7. 7 USB 8. 0 Troubleshooting 9. 0 Specifications 10 10 12 13 16 17 17 19 22 23 05 Jul 2013 18:14 STRONG declares that this item complies with the basic requirements and other relevant regulations of directives CE 2004/108/EC and 73/23/EC, RoHS 2002/95/EC Subject to alterations. In consequence of continuous research and development technical specifications, design and appearance of products may change. All product names are trademarks or registered trademarks of their respective owners. All rights reserved. 1 PART 1 • English 1. 0 Instruction 1. 1 Safety Instructions DO NOT INSTALL YOUR RECEIVER: „„ a closed or poorly ventilated cabinet; directly on top of or under any other equipment; on a In surface which might obstruct the ventilation slots. [. . . ] “AV IN” will be displayed on the front LED display when the receiver is in VCR mode. Press the DTV/VCR button again to return to the digital TV content. Note:  The setting "Always" increases the power consumption in standby mode. The front panel LED remains green in standby! 7. 3 Channel Search To access the menu press MENU and select Channel Search. 7. 3. 1 Installation 7. 3. 1. 1 Satellite Selection Use the pq buttons to highlight the satellite your dish is aimed at. You can enter the right side with the tu buttons and return to the satellite list with EXIT. 7. 3. 1. 2 Configure the antenna settings for the selected satellite LNB Type:  Press tu or OK to show the list of LNB Types which is shown as frequencies. You also can enter customized frequencies by User Single or User Dual at the bottom of the list. The default setting Universal LNB (09750/10600) – the most used on the market. Toneburst:  enable or disable the toneburst switcher if available. To DiSEqC1. 0:  select the right port from up to 4 (if available) for the right LNB. To DiSEqC1. 1:  select the right port from up to 16 (if available) for the right LNB. To Motor:  using a motor, press tu to choose between DiSEqC1. 2 and GOTOX If depending on the motor type you use. Then press OK to show the menu for setting the position or GREEN for location. DiSEqC1. 2:  Move the motor to the right position for locking the signal like explained below. PART 1 • English Move Continue:  press tu for moving West/East. Store Position:  store the current motor position for selected satellite. A pop-up window will appear, in which the following settings can be made: Location:  Use tu to select one of the pre-set locations. If you know the coordinates of your place of residence, you can choose Manual and make the following extra adjustments: Longitude Direction:  Choose East or West. Longitude Angle: Use the NUMERIC buttons to enter the coordinate. Latitude Angle: When all settings have been made, press EXIT to save the data and leave the window. Move Auto will move the dish to the selected satellite automatically. For Move Continue, Move Step (1) and Goto Reference please see explanation above. [. . . ] 7. 7. 3 Movie Subtitle This subtitle function is only relevant in the Movie menu for movies which contain subtitle files in. srt or txt format. During playback, press SUBTITLE to select a language and confirm with OK. During playback of Movie files you can press SUBTITLE twice to change the subtitle settings described below: Subtitle Specific:  Choose subtitle size between Small, Normal and Big. Subtitle BG:  Choose subtitle background between White, Transparent, Gray and Yellow-Green. [. . . ]