User manual STIHL FS94

[. . . ] { STIHL FS 94 Instruction Manual Manual de instrucciones Instruction Manual 1 - 46 Manual de instrucciones 47 - 98 English Contents Guide to Using this Manual Safety Precautions and Working Techniques Approved Combinations of Cutting Attachment, Deflector, Handle and Harness Mounting the Loop Handle Mounting the Deflector Mounting the Cutting Attachment Fuel Fueling Fitting the Harness Balancing the Trimmer/Brushcutter Starting / Stopping the Engine Operating Instructions Cleaning the Air Filter Engine Management Adjusting the Carburetor Spark Arresting Screen in Muffler Spark Plug Rewind Starter Storing the Machine Sharpening Metal Cutting Blades Replacing Nylon Line Replacing the Cutting Blade Inspection and Maintenance by User Inspections and Maintenance by Dealer Maintenance and Care Main Parts Specifications 2 3 15 16 18 19 22 23 24 24 25 27 28 28 29 29 29 31 31 31 32 33 33 34 35 37 39 This instruction manual is protected by copyright. All rights reserved, especially the rights to reproduce, translate and process with electronic systems. Printed on chlorine-free paper Printing inks contain vegetable oils, paper can be recycled. Special Accessories Maintenance and Repairs Disposal STIHL Incorporated Federal Emission Control Warranty Statement STIHL Incorporated California Exhaust and Evaporative Emissions Control Warranty Statement Trademarks 40 40 41 41 Allow only persons who fully understand this manual to operate your trimmer / brushcutter. [. . . ] N Slide the lower guide slot of the skirt (4) onto the deflector (1) – it must snap into position. Push the blade (5) into the upper guide slot on the skirt and line it up with the first hole. NOTICE The thrust plate (1) on the gearhead is necessary for mounting cutting attachments. STIHL FS 94 R 002BA383 KN 19 002BA266 KN Lay your trimmer on its back so that the cutting attachment mounting face is pointing up. 2 English N Insert the stop pin (7) in the bore (8) in the gearhead as far as stop, apply slight pressure. Rotate shaft or cutting attachment until the stop pin slips into position and blocks the shaft. STIHL FixCut 25-2, STIHL FixCut 30-2, STIHL PolyCut 20-3 3 N 4 5 Mounting the Cutting Attachment WARNING Use a deflector that matches the cutting attachment – see "Mounting the Deflector". N Go to "Mounting the Mowing Head" or "Mounting the Metal Cutting Attachment". 002BA385 KN 1 Depending on the cutting attachment, it may be necessary to use the nut (3), rider plate (4) and thrust washer (5). These parts are included in a kit supplied with the machine and are also available as special accessories. Blocking the Shaft 002BA267 KN Mounting the Mowing Head Keep the instruction leaflet for the mowing head in a safe place. STIHL SuperCut 20-2 STIHL AutoCut 25-2, STIHL TrimCut 31-2, STIHL DuroCut 20-2, N Screw the mowing head counterclockwise on to the shaft (1) as far as stop. N N 2 8 7 7 002BA384 KN NOTICE Remove the tool used to block the shaft. The output shaft (2) must be blocked with the stop pin (7) to mount or remove cutting attachments. The stop pin is included with the machine and is available as a special accessory. 20 STIHL SuperCut 20-2 STIHL AutoCut 25-2, STIHL TrimCut 31-2, STIHL DuroCut 20-2, STIHL FS 94 R English STIHL FixCut 25-2, STIHL FixCut 30-2, STIHL PolyCut 20-3 N Unscrew the mowing head clockwise. Check direction of rotation of cutting attachment 7 6 681BA108 KN Mounting Metal Cutting Attachments WARNING Wear protective gloves to reduce the risk of direct contact with the sharp cutting edges. 1 2 4 3 5 2 681BA211 KN The skirt and line limiting blade are not required on the deflector for grass cutting blades 230-4 (1) and 230-8 (2) or the brush knife (3) – see "Mounting the Deflector". Lay your trimmer on its back with the cutting attachment mounting face pointing up: The cutting edges of (1) may point in either direction. 1 1 N Place the cutting attachment (1) on the thrust plate (2). WARNING 2 3 Direction of rotation is indicated by an arrow on the inside of the deflector. Collar (see arrow) must engage the cutting attachment's mounting hole. [. . . ] STIHL Incorporated will not be liable to warrant failures of warranted parts caused by the use of a non-exempted add-on or modified part. The warranty on emissions-related parts will be interpreted as follows: 1. Any warranted part that is not scheduled for replacement as required maintenance in the written instructions required in the Emission Warranty Parts List (see below) must be warranted for the warranty period defined in Subsection COVERAGE BY STIHL INCORPORATED, see above. If any such part fails during the period of warranty coverage, it must be repaired or replaced by the manufacturer according to Subsection (4) below. [. . . ]