User manual STEINEL IR QUATTRO HD KNX

[. . . ] However, under certain conditions it may be possible for an installation in these applications. Please contact the nearest Miele dealer or the Miele Technical Service Department with specific requirements. This dishwasher must be installed under a continuous countertop secured to adjacent cabinetry. Do not, under any circumstances, cut the intake hose or submerge in liquid. [. . . ] The drain hose connection at the rear of the dishwasher can be turned to allow the hose to be angled to the right or left. Exercise care when sliding the dishwasher in or out, to prevent damaging the power cord or hoses. ^ Make a 2" x 4" (5 x 10 cm) cut out in the side or bottom of the cabinet adjoining the dishwasher. This cut out is necessary for connections to pass through. 13 Installation 5. Level the legs ^ The rear leveling legs can be adjusted with a T20 Torx screwdriver by turning the screws at the front of the slide skis. Do not use a power screwdriver. ^ Adjust the front leveling legs by pushing on the feet with a slotted screwdriver. ^ Tipping the machine slightly backwards, if posssible will make adjusting the front legs easier. Stainless Steel Full size 4 047 341 4 047 361 3 280 742 3 298 210 Slimline 4 312 770 4 312 780 4 316 721 ^ To remove the filler strips from the control panel, place the panel printed side up, and gently push down near the bottom of the control panel. This will release the mounting bolts from their slots. 18 Installation 8. Install the custom door panel A custom door panel matching the kitchen cabinetry can be installed using the provided templates and bracket. As long as the panel length calculated is within the Range of Panel Sizes listed, the custom panel should fit without a problem. Range of Panel Sizes G 636 - G 698 Length: Width: 19" - 23 3/4" (483 - 603 mm) 23 1/2" (598 mm) G 801 - G 832 Length: Width: 21" - 25 3/4" (533 - 654 mm) 17 1/2" (445 mm) G 836 - G 898 Length: Width: X = Panel length A = Height to the underside of the countertop B = Control panel height* C = Toe Kick Height Length X: Determined using the following calculation: X = A ­ B ­ C *Control panel height is determined by the height of the drawers in the cabinets. It should be snug at the top and neatly aligned with the adjacent cabinetry. If it is not aligned properly, loosen the Torx screws and readjust the panel Once the door panel is positioned correctly: ^ Open the dishwasher door. ^ Use the provided caps to plug the locking screw access holes. ^ Attach the panel to the dishwasher by lining up the bracket tabs with the slots on the door. ^ Open the dishwasher door slightly. If the locking screws on the edge of the dishwasher door can not be reached, the dishwasher will have to be pulled out of its opening a few inches. 25 Installation 9. If the steam deflector is installed, the mounting bracket holes must align with the slots in the steam deflector. Make certain that the white rubber seal located at the top, outer edge of the dishwasher is tight against the bottom of the countertop. Do not drill any additional holes through any part of the wash cabinet. If in doubt on how to secure the dishwasher, please call Miele's Technical Service Department. ^ Using flat head screws, secure the dishwasher to the countertop by screwing through both the mounting bracket and the steam deflector. 26 Installation For openings exactly 17 3/4" (45 cm) or 23 5/8" (60 cm) wide: should only be used for securing the dishwasher if the opening is exactly 17 3/4" (45 cm) wide (slim line models) or 23 5/8" (60 cm) wide (full size models). Use of this method on larger openings can damage the machine and cause leaks. Be careful not to screw into an adjacent appliance. , The side mounting holes ^ Open the dishwasher door and remove the caps covering the mounting holes on the outer edge of the wash cabinet. ^ Fasten the dishwasher to the adjacent cabinets using the supplied screws and bushings. [. . . ] Specifications The dishwasher comes equipped with a 4 ft (1. 2 m) power cord with a molded plug for connection to 120 V, 60 Hz, 15 A grounded receptacle. 15 A , Improper connection of the equipment grounding conductor can result in electric shock. Do not modify the plug provided with the appliance; if it will not fit the outlet, have a proper outlet installed by a qualified electrician. If there is any question concerning the proper electrical connection or grounding of this appliance to the power supply, please consult a licensed electrician or call Miele's Technical Service Department: USA 1-800-999-1360 CDN 1-800-565-6435 33 Installation Power outlet The power outlet for the appliance must be installed within a cabinet, on a wall adjacent to the undercounter space in which the dishwasher is located. An opening through the partition between the compartments of 1 1/2" (3 to 4 cm) can be made to allow the plug to pass through. [. . . ]