User manual STEINEL HF 360 COM 2

[. . . ] ensure that the connection data on the data plate (fusing, voltage and frequency) match the mains electrical supply. Extension cords do not guarantee the required safety of the appliance (e. g. maritime use or for use in mobile installations such as recreational vehicles or aircraft. However, under certain conditions it may be possible for an installation in these applications. [. . . ] The program must be canceled. Adjusting the temperature The temperature can be changed up to 6 minutes after the program start. ^ Press and hold the "Cancel" button until the display shows: Cancel Adjusting the spin speed The spin speed can be adjusted anytime until the beginning of the final spin. Adjusting the options The wash water will be drained away. The options "Extended" or "Sensitive" can be selected or deselected up to 6 minutes after the program start. The "Buzzer" option can be selected or deselected at any time. 25 Using the washer Preparing your appliance for an extended vacation If you elect to turn off the water to your home for an extended period of time, please note that this may not be enough to reduce the risk of a leak. To be completely safe, you must turn off the water supply to each individual appliance. This means under the sink for a dishwasher, at the laundry bib for your washer, etc. The drum door cannot be opened if: ­ the water temperature is greater than 130°F (55°C). If you attempt to open the door while the washer is in one of the above statuses "Machine locked" will appear in the display. Adding/removing laundry during a wash program ^ Press and hold the door button until the door opens. Note: Once the program has started the washer can not make adjustments of the load size. X Machine locked 26 Cleaning and care , Before cleaning or maintenance, Desclaing the washer If the correct amount of detergent is dispensed, the machine should not need to be descaled. ^ If the washer needs to be descaled, use a descaling agent with corrosion protection. Use as directed on the packaging. disconnect the power supply by unplugging the unit or manually "tripping" the circuit breaker. , Do not use a hose to wash down the washer. Cleaning the exterior and control panel ^ Clean the exterior of the washer with a mild solution of non-abrasive detergent or soap and water, and wipe dry with a soft cloth. ^ Clean the filter under running water and carefully remove any large particles. Both filters must be put back in place after cleaning. 29 Cleaning and care Clean the drain pump Occasionally, small objects (buttons, coins, etc. ) may become trapped in the lint trap. If the machine does not drain completely, the lint trap should be checked to ensure that it is free of foreign objects. ^ Open the detergent dispenser drawer. ^ Remove and clean the lint trap. ^ Check that the impeller (in the back of the chamber) rotates freely by spinning it with your hand. ^ Remove the tool. ^ Press the "Door" button. ^ Return the lint trap and tighten into place. , If the lint trap lid is not tightened securely water will leak out when the machine is used. ^ Open the access panel. The lint trap lid is visible when the access panel is opened. 30 Frequently asked questions , Repairs to electrical appliances must only be carried out by a qualified and trained person in accordance with local and national safety regulations. Repairs and other work by unqualified persons could be dangerous. The following section will help you avoid placing a service call by identifying issues you may encounter while operating the machine: A wash program cannot be started Issue Possible cause Solution Check to determine if: ­ the washer is plugged in. The "child entrapment sensor" has reacted. 31 Frequently asked questions The display shows a fault message Issue Possible fault Fix 1) q p Drain fault Check drain ­ The drain is ­ Clean the drain filter and blocked. ­ the inlet hose is kinked. Water inlet fault Open water faucet o , Waterproof system activated Technical fault Call Technical Service The waterproof system Call Technical Service. Use less detergent in the next wash program, and follow the recommended amount on the detergent packaging. In the display flashes Anti-crease The machine has oversudsed. alternating with Check detergent 1) To turn off the fault message: ^ To turn the fault message off: Open the drum door or press the "Cancel" button until the fault message goes out. 32 Frequently asked questions General problems with the washer Issue The washer shakes during the spin cycle. [. . . ] If the machine is being connected only to a cold water supply, both the hot and cold water intake hoses must be attached to the cold water valve through the use of a Y adapter (available at a hardware store). Both hoses must be connected to a water source or the machine will not function properly. If the water pressure is greater that 145 psi (10 bar) a pressure reducer must be installed. If the water pressure is below 15 psi (1 bar) there will not be enough water available for a complete fill. [. . . ]