User manual STEINEL DUAL HF COM 1 AP

[. . . ] or mental abilities, or experience with the appliance should not use it without supervision or instruction by a responsible person. ~ Persons who lack physical, sensory Children Keep these operating instructions in a safe place and pass them on to any future user. SAVE THESE INSTRUCTIONS ~ Do not allow children to play on or in the appliance. Close supervision is necessary when the appliance is used near children. Keep children away from the washer when in use. ~ The drum door glass will be hot 4 IMPORTANT SAFETY INSTRUCTIONS Technical safety visible damage. ~ Do not install or use a washer with ~ Before connecting the machine, ~ Faulty components must only be replaced with genuine Miele spare parts. ~ Installation, repair and maintenance work should be performed by a Miele authorized service technician. [. . . ] Activate the Child Lock (if desired) The Child Lock prevents a program from being canceled. When pressing the "Start" button, do not press and hold the button. The washer shows the current cycle of the wash program under "STATUS". ^ Press the "OPTIONS" button until the "FAULT" indicator "Child Lock" lights. Deactivate the Child Lock ^ Press the "OPTIONS" button until the "FAULT" indicator "Child Lock" goes out. Once the program has finished, the Child Lock must be deactivated. , If a program was started without detergent, cancel the program first. Add detergent, then select and start a program again. 21 Using the washer 9. shrink or discolor) during the next wash cycle. ^ Check the folds of the door seal for any small articles which may have been trapped. ^ Activate the Child Lock for safety reasons. , Children, animals or foreign objects may find their way into the drum. Danger of injury and damage to the machine! 22 Using the washer Canceling a program A program can be canceled any time after a program start. Interrupting a program ^ Press the "Pause" button briefly. ^ Press the "Pause" button until the "STATUS" indicator "Drain/Spin" indicator lights. ^ Unscrew the inlet hose from the valve by turning the connector counterclockwise using a wrench if necessary. ^ Remove the rubber seal, 1, from the connector. ^ Using needle nose pliers, grasp the plastic filter, 2, and pull it out of the hose connector. ^ Clean the filter under running water and carefully remove any large particles. Both filters must be put back in place after cleaning. 28 Frequently asked questions , Repairs to electrical appliances must only be carried out by a qualified and trained person in accordance with local and national safety regulations. Repairs and other work by unqualified persons could be dangerous. The following section will help you avoid placing a service call by identifying issues you may encounter while operating the machine: A wash program cannot be started Issue Possible cause Solution Check to determine if: ­ the washer is plugged in. A "PROGRAMS" The washer has no indicator does not light power. The "child entrapment sensor" has reacted. 29 Frequently asked questions The program was canceled, the buzzer sounds and the "Start" button flashes. Issue Possible cause Solution ­ To turn off the fault message: Open the drum door or press and hold the "Pause/Hold to Cancel" button until the fault message goes out. The "FAULT" indicator ­ The drain is "Drain" lights. The "FAULT" indicator The water intake is "Intake" lights. Contact Technical Service. The "FAULT" indicators "Intake" and "Drain" light. The waterproof system has activated. The "STATUS" There is a fault. ­ Press "Start". 30 Frequently asked questions An error message is displayed at the end of a program. Issue Possible cause Solution ­ To turn off the fault message: Open the drum door or press and hold the "Pause/Hold to Cancel" button until the fault message goes out. [. . . ] If the machine is being connected only to a cold water supply, both the hot and cold water intake hoses must be attached to the cold water valve through the use of a Y adapter (available at a hardware store). Both hoses must be connected to a water source or the machine will not function properly. If the water pressure is greater that 145 psi (10 bar) a pressure reducer must be installed. If the water pressure is below 15 psi (1 bar) there will not be enough water available for a complete fill. [. . . ]