User manual SONY VPCEG24FX/P

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SONY VPCEG24FX/P. We hope that this SONY VPCEG24FX/P user guide will be useful to you.


SONY VPCEG24FX/P : Download the complete user guide (2114 Ko)

Manual abstract: user guide SONY VPCEG24FX/P

Detailed instructions for use are in the User's Guide.

[. . . ] If the device installation requires construction work, make sure to observe the following precautions. - Choose mounting hardware and an installation location that can support the weight of the device. - Inspect the device periodically. ● Handling and Maintenance • Do not place vinyl, plastic or rubber objects on the device, since this might discolor the panel. Do not use paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping cloths. [. . . ] • Condensation can occur in the device due to rapid, drastic changes in ambient temperature-when the device is moved from one location to another, or air conditioning is turned on or off, for example. If there is reason to believe that condensation might have occurred, leave the device for several hours until the condensation has completely dried out. • Be sure to observe the amplifier’s rated load impedance (see SPECIFICATIONS), particularly when connecting speakers in parallel. Connecting an impedance load outside the amplifier’s rated range can damage the amplifier. • When connecting the speakers with high impedance, be sure that the output total of each speaker does not exceed the rated output of the power amplifier. • ABOUT THE PROTECTION CIRCUIT This speaker system has an internal protection circuit that shuts off the speaker unit when an excessive input signal is applied. If the speaker unit emits no sound, reduce the volume level of the amplifier immediately. • Do not place the speaker on the ground with the grille faced down. • Do not touch the speaker driver unit. LF HF Coverage angle (500 Hz – 4 kHz on average) Nominal impedance Power rating NOISE (IEC, 100h) *1 PGM MAX Sensitivity (1W, 1m) *2 Maximum SPL (Calculated, 1m) *3 Frequency range (-10 dB) *2, *4 Crossover frequency Connector Transformer taps 70 V 100 V Overload protection Magnetically shielded Dust and water resistant *5 Enclosure Shape Cabinet material Baffle material Grille material Finish Dimensions (Speaker only) (W × H × D in vertical cabinet orientation) Net weight (Speaker only, 1 piece) Packaging Connections • Before connecting the device to a power amplifier, turn off the power for all devices. Before turning the power on or off for all devices, set all volume levels to minimum. • Use only speaker cables for connecting speakers to the speaker connectors. 3 Plug the Euroblock connector into the socket in the speaker. 4 ATTACH THE MOUNTING BRACKET AND SAFETY WIRE Euroblock connector 1 Attach the mounting bracket and safety wire to the speaker. The way to attach the mounting bracket depends on the orientation of the speaker (vertical or horizontal). Vertical installation Mounting bracket NOTE Use a flat-blade screwdriver with a blade less than 3 mm (0. 1 in. ). Less than 3 mm (0. 1 in. ) There are two acceptable wiring methods. Vertical CAUTION When connecting with low impedance, take note of the combined resistance. Using Loop-Through Terminals For this method, cables are connected from terminals 1 and 4 to the subsequent speaker. If the Euroblock connector is disconnected from a speaker, all subsequent speakers will not work. This can be useful to identify which speaker has a problem. Angle adjustment bolt Safety wire Stopper screw (VXS8/VXS8W only) 4 Attach the terminal cover. Terminal cover Horizontal installation Stopper screw (VXS8/VXS8W only) Angle adjustment bolt Horizontal From amplifier or previous speakers NOTE Mounting bracket can be attached in reverse direction. To subsequent speakers To subsequent speakers 5 (If installing the speaker to the wall) turn the speaker horizontally to set the angle. 6 Make sure the mounting bracket is seated against the bracket base, then tighten the supplied bolt (indication of torque: 6. 5 N·m). 2 Set the desired vertical angle of the speaker. Loosen the angle adjustment bolt with the supplied hexagon wrench, adjust the angle of the speaker, and tighten the angle adjustment bolt to fix the speaker (indication of torque: 8 N·m). • (VXS8/VXS8W only) When installing the speaker to the wall with a vertical angle of 30° or less, attach the supplied stopper screw. 1 INSTALL THE BRACKET BASE ONTO THE WALL /CEILING 1 Put the bracket base onto the wall/ceiling and mark the position for the screws/bolts and cables. The diameter of the screw/bolt holes at the four corners is M6, and speaker cables hole at the center is ø11 mm. [. . . ] • (VXS8/VXS8W only) When installing the speaker to the wall with a vertical angle of 30° or less, attach the supplied stopper screw. 1 INSTALL THE BRACKET BASE ONTO THE WALL /CEILING 1 Put the bracket base onto the wall/ceiling and mark the position for the screws/bolts and cables. The diameter of the screw/bolt holes at the four corners is M6, and speaker cables hole at the center is ø11 mm. 2 Make holes through the wall/ ceiling for the bolts and cables, as required, and feed the bolts and cables from the amplifier through the holes, as shown. 4 Pass cables through the gap at the lower part of the bracket cover, and put the bracket cover on the bracket base. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SONY VPCEG24FX/P




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SONY VPCEG24FX/P will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.