User manual SONY VPCEG24FX/L

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SONY VPCEG24FX/L. We hope that this SONY VPCEG24FX/L user guide will be useful to you.


SONY VPCEG24FX/L : Download the complete user guide (2114 Ko)

Manual abstract: user guide SONY VPCEG24FX/L

Detailed instructions for use are in the User's Guide.

[. . . ] If there is reason to believe that condensation might have occurred, leave the device for several hours until the condensation has completely dried out. • Be sure to observe the amplifier’s rated load impedance (see SPECIFICATIONS), particularly when connecting speakers in parallel. Connecting an impedance load outside the amplifier’s rated range can damage the amplifier. • When connecting the speakers with high impedance, be sure that the output total of each speaker does not exceed the rated output of the power amplifier. [. . . ] • ABOUT THE PROTECTION CIRCUIT This speaker system has an internal protection circuit that shuts off the speaker unit when an excessive input signal is applied. If the speaker unit emits no sound, reduce the volume level of the amplifier immediately. • Place the speaker on a flat and smooth surface. Sensitivity (1W, 1m) *2 Maximum SPL (Calculated, 1m) *3 Frequency range (-10 dB) *2 Subwoofer filter Satellite filter Satellite impedance Connector Location • Do not place the device in an unstable position where it might accidentally fall over. • Do not place the device in a location where it may come into contact with corrosive gases or salt air. • Construction work should be carried out in accordance with constructionrelated law and always by a professional constructor. If the device installation requires construction work, make sure to observe the following precautions. - Choose mounting hardware and an installation location that can support the weight of the device. • When transporting or moving the device, always use two or more people. Attempting to lift the device by yourself may damage your back, result in other injury, or cause damage to the device itself. Transformer taps Overload protection Magnetically shielded Enclosure Finish 70 V 100 V Shape Cabinet material Dimensions (Speaker only) Net weight (Speaker only) Connections • Before connecting the device to a power amplifier, turn off the power for all devices. Before turning the power on or off for all devices, set all volume levels to minimum. If the wire is too long, should the speaker fall, the wire may snap as a result of too much strain. 1 Pass the safety wire through the eyebolt on the rear of the speaker. Eyebolt 2 INSTALL THE SPEAKER Installing on the wall (using the included brackets) 1 Place the bracket base on the wall and mark the position for screws/bolts. The diameter of seven holes for screw/bolt (not included) is ø6. 5 mm. 2 Make holes in the wall for the bolts, as required, and feed the bolts through the holes. 4 Attach the mounting bracket to the speaker with the included screws with captive washer. The narrow edge of the mounting bracket should be oriented downward. Bracket base WARNING • Do not use the included brackets for ceiling installation. Pre-installation (Preparation of the cable) Use stranded wire for cables attached to the Euroblock connector. Strip their insulation as shown in the figure and connect them. About 7 mm (0. 3 in. ) Installing on the ceiling (using the optional UB-DXR8) To determine the appropriate size of the UB-DXR8, download the “U BRACKET OWNER’S MANUAL” from the following manual library site. http://www. yamaha. co. jp/manual/ 1 Assemble two L-shaped brackets into a U-shape using the M5 × 10 screws included with the UB-DXR8 as shown below. Peel off the sheet from each rubber spacer (14 mm thickness; included with the speaker), and attach the spacers to the inside of each bracket arm aligning the holes so that the hexagon bolts can be inserted. M5 × 10 NOTE Do not plate stranded wires by solder. [. . . ] Peel off the sheet from each rubber spacer (14 mm thickness; included with the speaker), and attach the spacers to the inside of each bracket arm aligning the holes so that the hexagon bolts can be inserted. M5 × 10 NOTE Do not plate stranded wires by solder. Doing so will cause the wire to break. 2 Pass the bracket of the safety wire through the loop on the other end, and pull tight up against the eyebolt. 1 CONNECT THE WIRING TO THE CONNECTOR Connect the cable from the amplifier to the “INPUT” socket, and the cable being connected to other speakers to the “SATELLITE SPEAKERS” socket. A signal input to CH1 of INPUT is output from ST1 of SATELLITE SPEAKERS, and signal input to CH2 of INPUT is output from ST2 of SATELLITE SPEAKERS. For VXS10ST/VXS10STW, connect the included 5-pin Euroblock connector as shown below and set the appropriate wattage when using 100 V/70 V line. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SONY VPCEG24FX/L




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SONY VPCEG24FX/L will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.