User manual SONY TDG-PJ1

[. . . ] As the main plug is used to disconnect the unit from the mains, connect the unit to an easily accessible AC outlet. Should you notice an abnormality in the unit, disconnect the main plug from the AC outlet immediately. Do not expose batteries or apparatus with batteryinstalled to excessive heat such as sunshine, fire or the like. The unit is not disconnected from the mains as long as it is connected to the AC outlet, even if the unit itself has been turned off. [. . . ] RDS is available only for FM stations. * * Not all FM stations provide RDS service, nor do they provide the same type of services. If you are not familiar with the RDS services in your area, check with your local radio stations for details. 2 3 4 5 Tune to the preset station you want to create an index name for (page 41). Press V/v repeatedly to select "NAME IN", then press or b. The cursor flashes and you can enter a character. 6 Press V/v to select a character, then press B/b to move the input position backward and forward. You can enter up to 8 characters to name the station. Tips · You can select the character type as follows by pressing V/v. Alphabet (upper case) t Numbers t Symbols · To enter a blank space, press b without selecting a character. Simply select a station on the FM band using Direct Tuning (page 40), Automatic Tuning (page 39), or Tuning with Preset Station (page 41). When you tune to a station that provides RDS services, "RDS" lights up and the Program Service name appears on the display panel. Note RDS may not work properly if the station you tuned to is not transmitting the RDS signal or if the signal strength is weak. Tip While a Program Service name is displayed, you can check the frequency by pressing DISPLAY repeatedly (page 37). If you made a mistake Press B/b until the character you want to change flashes, then press V/v to select the correct character. 7 Press . The name you entered is registered. Note (Europe, Australia and Taiwan models only) When you name an RDS (Radio Data System) station and tune to that station, the Program Service name appears instead of the name you entered. 42GB Note Enjoying Surround Sound You cannot select "A. DIRECT" when you select BD/DVD and GAME as input. Selecting the sound field This receiver can create multi channel surround sound. You can select one of the optimized sound fields from the receiver's pre-programmed sound fields. Auto Format Direct (A. F. D. ) mode The Auto Format Direct (A. F. D. ) mode allows you to listen to high fidelity sound and select the decoding mode for listening to a 2 channel stereo sound as multi channel sound. x A. F. D. Auto) SOUND FIELD +/­ Press SOUND FIELD +/­ repeatedly to select the sound field you want. You can also press 2CH/A. DIRECT, A. F. D. , MOVIE/HD-D. C. S. or MUSIC on the receiver. Presets the sound as it was recorded/encoded without adding any surround effects. Its vertical equipment gives a dimension of presence and depth. x NEO6 CIN (Neo:6 Cinema) Performs DTS Neo:6 Cinema mode decoding. A source recorded in 2 channel format is decoded into 7 channels. Music mode You can take advantage of surround sound simply by selecting one of the receiver's preprogrammed sound fields. They bring the exciting and powerful sound of concert halls into your home. 44GB x NEO6 MUS (Neo:6 Music) Performs DTS Neo:6 Music mode decoding. This setting is ideal for normal stereo sources such as CDs. When headphones are connected You can only select the following sound fields if the headphones are connected to the receiver. x HP 2CH (Headphones 2CH) This mode is selected automatically if you use headphones (except Analog Direct). Standard 2 channel stereo sources completely bypass the sound field processing and multi channel surround formats are downmixed to 2 channels except LFE signals. x HP DIR (Headphones Direct) This mode is selected automatically if you use headphones and when "A. Outputs the analog signals without processing by the equalizer, sound field, etc. If you connect a subwoofer This receiver will generate a low frequency signal for output to the subwoofer when there is no LFE signal, which is a low-pass sound effect output from a subwoofer to a 2 channel signal. However, the low frequency signal is not generated for "NEO6 CIN" or "NEO6 MUS" when all speakers are set to "LARGE". In order to take full advantage of the Dolby Digital bass redirection circuitry, we recommend setting the subwoofer's cut off frequency as high as possible. · "PLII MV", "PLIIX MV", "PLII MS", "PLIIX MS", "PLIIZ", "NEO6 CIN" and "NEO6 MUS" also do not work when the speaker pattern is set to 2/0 or 2/0. 1. · You cannot select "PLIIX" and "PLIIZ" at the same time. ­ "PLIIX" is available only when the speaker pattern is set to a setting with surround back speaker(s). [. . . ] · The signal strength of the stations is too weak with automatic tuning. · Make sure you set the tuning scale correctly (when tuning in AM stations with direct tuning) (page 40). · No stations have been preset or the preset stations have been cleared (when tuning by scanning preset stations is used). · Press DISPLAY repeatedly so that the frequency appears on the display panel. [. . . ]