User manual SONY SDM-N50

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ­ Reorient or relocate the receiving antenna. [. . . ] Press the m/M buttons to select (PICTURE ADJUST) and press the OK button. Press the m/M buttons to select " BRIGHTNESS" and press the OK button. Press the m/M buttons to adjust the brightness and press the OK button. 2 4 Press the m/M buttons to select the desired mode and press the OK button. The screen brightness is changed as the mode turns to HIGH t MIDDLE t LOW, and the power consumption is reduced. When you select "USER, " the screen brightness turns to the level you adjusted with the ECO button on the front of the monitor. For more information, see "Reducing the power consumption (ECO mode)" on page 17. 3 4 x Adjusting the BACKLIGHT If the screen is too bright, adjust the backlight to make the screen easier to see. Note The backlight cannot be adjusted when the ECO mode is set to "HIGH, " "MIDDLE, " or "LOW" (page 17). x Adjusting the SMOOTHING If the picture displayed at the FULL2 or FULL1 mode of ZOOM is not smooth, use the picture smoothing function. Press the m/M buttons to select (PICTURE ADJUST) and press the OK button. The PICTURE ADJUST menu appears on the screen. 1 Press the MENU button. Press the m/M buttons to select (PICTURE ADJUST) and press the OK button. The PICTURE ADJUST menu appears on the screen. 2 2 12 3 Press the m/M buttons to select "SMOOTHING" and press the OK button. The smoothing effect becomes stronger in the order of TEXTtSTANDARDtGRAPHICS. Click [END] on the screen to turn off the test pattern. x Fine tuning the color temperature 1 Press the MENU button. Press the m/M buttons to select "ADJUST" and press the OK button. The fine tuning menu for color temperature appears on the screen. USER ADJUSTMENT 128 128 128 2 4 3 5 6 R G B 7 1 6 0 0 x 1 2 0 0 / 6 0Hz EX I T 4 8 Press the m/M buttons to select R (Red) or B (Blue) and press the OK button. Then press the m/M buttons to adjust the color temperature and press the OK button. Since this adjustment changes the color temperature by increasing or decreasing the R and B components with respect to G (green), the G component is fixed. The new color setting is stored in memory and automatically recalled whenever "USER" is selected. The COLOR menu appears on the screen. 5 14 GAMMA menu You can associate the picture's color shade on the screen with the picture's original color shade. GAMMA GAMMA 1 GAMMA 2 GAMMA 3 MENU POSITION menu You can change the menu position if it is blocking an image on the screen. MENU POS I T I ON 1 6 0 0 x 1 2 0 0 / 6 0Hz EX I T 1 6 0 0 x 1 2 0 0 / 6 0Hz EX I T x Selecting the GAMMA 1 Press the MENU button. Press the m/M buttons to select the desired mode and press the OK button. 1 Press the MENU button. Press the m/M buttons to select (MENU POSITION) and press the OK button. Press the m/M buttons to select the desired position and press the OK button. You can choose one of 9 positions where the menu will appear. 2 2 3 3 ZOOM menu The monitor is set to display the picture on the screen in full, irrespective of the picture's mode or resolution in the default setting (FULL2). [. . . ] It takes a few minutes for the display to become bright after turning on the monitor. The screen might turn darker, depends on ECO mode you selected. GB Wavy or elliptical pattern (moire) is visible. After turning off the main power, the 1 (power) indicator stays bright for a while. · Adjust the pitch and phase (analog RGB signal only) (page 13). · Adjust the pitch and phase (analog RGB signal only) (page 13). [. . . ]