User manual SONY SDM-E96D

[. . . ] This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ­ Reorient or relocate the receiving antenna. ­ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ] Whites will change from a bluish hue to reddish hue as the temperature is lowered from 9300K (default setting) to 6500K. When using the SDM-X52 model, it is not necessary to set the resolution. Since this adjustment changes the color temperature by increasing or decreasing the R and B components with respect to G (green), the G component is fixed. The new color setting is stored in memory for USER ADJUSTMENT and automatically recalled whenever USER is selected. You can associate the picture's color shade on the screen with the picture's original color shade. If the picture displayed at the FULL2 or FULL1 mode of ZOOM is not smooth, use the picture smoothing function. When you set the (ZOOM) menu to REAL, the (SMOOTHING) menu is not available. 1024 × 768 (SDM-X52), 1280 × 1024 (SDM-E96D/X82) resolution signals are shown only in REAL mode and SMOOTHING is not possible. You can also view the picture in its actual aspect ratio or resolution. Therefore, black bands may appear at the top and bottom of the picture depending on the signal. When using the SDM-E96D/X82 model with 1280 × 1024 resolution signals, the above mentioned settings are not available. Check that the video signal cable is properly connected and all plugs are firmly seated in their sockets (page 7). XProblem caused by a connected computer or other equipment, and not caused by the monitor · the computer is in the power saving mode. Check that your graphics board is attached to the computer properly. " If OUT OF SCAN RANGE appears on the screen (page 19), xProblem caused by a connected computer or other equipment, and not caused by the monitor · check that the video frequency range is within that specified for the monitor. If you replaced an old monitor with this monitor, reconnect the old monitor and then adjust the computer's graphics board in the following ranges. Horizontal frequency: 28 ­ 61 kHz (SDM-X52) 28 ­ 92 kHz (SDM-E96D/X82) Vertical frequency: 56 ­ 75 Hz (SDM-X52) 56 ­ 85 Hz (SDM-E96D/X82) Resolution: 1024 × 768 or less (SDM-X52) 1280 × 1024 or less (SDM-E96D/X82) · If you replaced an old monitor with this monitor, reconnect the old monitor and do the following. Select "SONY" from the "Manufacturers" list and select "SDM-X52" or "SDMX72" or "SDM-X82" from the "Models" list in the Windows device selection screen. If "SDMX52" or "SDM-E96D" or "SDM-X82" does not appear in the "Models" list, try "Plug & Play" or install the information file for this monitor using the Windows Monitor Information Disk. When connecting a Macintosh computer, use an adapter (not supplied) if necessary. Isolate and eliminate any potential sources of electric or magnetic fields such as other monitors, laser printers, electric fans, fluorescent lighting, or televisions. Move the monitor away from power lines or place a magnetic shield near the monitor. [. . . ] These are related to another group of environmental toxins, PCBs, which are suspected to give rise to similar harm, including reproductive damage in fisheating birds and mammals, due to the bioaccumulative* processes. Flame retardants have been found in human blood and researchers fear that disturbances in foetus development may occur. TCO'95 demand requires that plastic components weighing more than 25 grams must not contain organically bound chlorine and bromine. Your choice has provided you with a product developed for professional use. [. . . ]