User manual SONY RM-LP204M

[. . . ] 8 Using the lists ] ] } Tip Under normal conditions, the batteries should last for about 3 months. When the remote no longer operates the receiver, replace all the batteries with new ones. Notes · Do not leave the remote in an extremely hot or humid place. · Do not mix the alkaline batteries and other kinds of batteries. · Do not expose the remote sensor of the receiver to direct sunlight or lighting apparatuses. [. . . ] INPUT A INPUT B INPUT VIDEO INPUT SELECT MEMORY BRIGHT + BRIGHT ­ CONTRAST + CONTRAST ­ ZOOM + ZOOM ­ SHIFT + SHIFT ­ FOCUS + FOCUS ­ Switches to the input from INPUT A jacks. Adjusts the lens shift of the picture. If you have programmed the remote to control nonSony components, note the following: ­ All the items may not appear when you select a component. ­ All the items displayed may not function. Tip Location of parts and basic remote operations Do the following procedure to perform set up menu operations on the DVD player. 2 Press the i button repeatedly to display the SUB menu. To display Do this TOP MENU DVD MENU SET UP Press TOP MENU button. Select "SET UP" in the SUB menu. 3 Use the control button to perform menu operations on the DVD player. To display the DVD menu, use the AV MENU button (page 7). a) "SIDE A/B" appears for non-Sony LD players. d) Only with the Sony CD changer. 11GB Using the lists Chart of lists See the tree diagram below for the list hierarchy. ­ "TAPE A/B" is displayed and tape deck A and B switch automatically each time you press the easy scroll key, etc. 2 Move the easy scroll key to select the sound field, then press the key to enter the selection. A display example If you selected 2ND ROOM or 3RD ROOM (North American model only) NORMAL SURROUND C. STUDIO EX A C. STUDIO EX B p C. STUDIO EX C To turn off the sound field Move the easy scroll key to select the source for 2nd room or 3rd room, then press the key. Move the easy scroll key to select either "AUTO DECODING" or "2CH STEREO" in the sound field list in the display. Tip You can sort the sound field list (page 18). 14GB Programming the remote You can customize the remote to match the components connected to your receiver. You can even program the remote to control nonSony components and also Sony components that the remote is normally unable to control. The procedure below uses as an example a case in which a Aiwa VCR is connected to the VIDEO 2 jacks on the receiver. Before you begin note that: ­ You cannot change the settings of TUNER and PHONO. To cancel programming Starting macro play 1 Press FUNCTION. The function list appears. Using the lists USER1 USER2 p MACRO1 MACRO2 2 Move the easy scroll key to select "MACRO1" or "MACRO2", then press the key to enter the selection. The IR codes appear in the display window as they are performed. Notes · Pressing any of the following buttons during a macro play operation will cancel the macro play sequence before it is complete. ­ AV ?/1 ­ ?/1 ­ SYSTEM STANDBY ­ SOUND FIELD ­ FUNCTION ­ RM SET UP · When the Macro Play function does not work properly, set "WAIT TIME" between each operation. Move the easy scroll key to select "Exit" or "Cancel" during any step, then press the key to enter the selection. Tips · In step 6, when "*" is displayed in front of the function, the function is pre-programmed. · In step 3 and 7, when "NO SET" is displayed after the program number, the codes have not been programmed. 17GB Using the RECEIVER menu 1 Press I repeatedly. The RECEIVER menu appears. <RECEIVER> p TEST TONE SB DECODING NIGHT MODE Other operations Sorting the sound field list You can arrange the order of sound field list. 1 Press RM SET UP. The set up list appears. IR SET p MENU EDIT AUTO POWER BACK LIGHT 2 Move the easy scroll key to select the item you want to set, then press the key to enter the selection. Each time you press the key, the setting changes. For details on each items, refer to the operating instructions supplied with the receiver. You can set the following items; · TEST TONE: Turns on or off the test tone. · TRIGGER OFF*: Turns off the TRIGGER function. * North American model only. 2 Move the easy scroll key to select "MENU EDIT", then press the key to enter the selection. The MENU EDIT list appears. <MENU EDIT> p SOUND FIELD FUNCTION SUB menu 3 Move the easy scroll key to select "SOUND FIELD", then press the key to enter the selection. The sort list appears. p AUTO DECODING 2CH STEREO ANALOG DIRECT 4 Move the easy scroll key to select the menu you want to move, then press the key to enter selection. When you press the key, "p" changes to "=". AUTO DECODING = 2CH STEREO ANALOG DIRECT 5 Move the easy scroll key to select the position you want to move the menu to, then press the key to enter selection. When you press the key, "=" changes to "p". [. . . ] p [VIDEO 1 ] [VIDEO 2 ] [VIDEO 3 ] 2 Move the easy scroll key to select "AUTO POWER", then press the key to enter the selection. 4 Move the easy scroll key to select the SUB menu you want to sort, then press the key to enter the selection. The AUTO POWER list appears. Sort?[VIDEO 1 ] p *CH+ *CH*INPUT SELECT 5 Move the easy scroll key to select the menu you want to move, then press the key to enter selection. When you press the key, "p" changes to "=". Sort?[VIDEO 1 ] = *CH+ *CH*INPUT SELECT 20GB 3 Move the easy scroll key to select "On" or "Off", then press the key to enter the selection. Adjusting the contrast of the display You can adjust the contrast of the display. When you select "On", the TV INPUT list appears. <TV INPUT> p TV-VIDEO1 TV-VIDEO2 TV-VIDEO3 1 Press RM SET UP. The set up list appears. [. . . ]