User manual SONY RCD-W10 annexe 1

[. . . ] 4-242-051-11(1) Compact Disc Recorder Operating Instructions Owner's Record The model and serial numbers are located on the rear panel. Refer to them whenever you call upon your Sony dealer regarding this product. Model No. Serial No. RCD-W50C/W10 ©2002 Sony Corporation WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To prevent fire, do not cover the ventilation of the apparatus with newspapers, table-cloths, curtains, etc. To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the apparatus. [. . . ] · When "PMA Writing" appears in the display: The unit is currently updating the track information. 16 If "Auto Cut" appears in the display (Auto Cut Function) There has been no sound input for about 30 seconds during recording. The 30 seconds of silence are replaced by a blank of about 3 seconds and the unit changes to recording pause. If the unit continues pausing for about 3 minutes after the Auto Cut Function activated, recording stops automatically. Note that this function does not activate if the unit has started recording from a blank portion or is synchro-recording from a CD on DECK A. Tip Insert the silence into the end of the song (The function of adding Post Gap) You can insert the silence of 2 seconds between the songs, when recording more than two tracks at once. · When the disc of DECK A changes to the next disc during Synchro-Recording. (RCDW50C only) To use the function of adding Post Gap Set "Post Gap" of the setup menu to "On" during stop. For details, see "Using the Setup Menu" on page 28. Recording/Editing You can turn off the Auto Cut Function. For details, see "To turn off the Smart Space Function and Auto Cut Function" below. Note that when you turn off the Auto Cut Function, the Smart Space Function is also turned off automatically. Using the SBM (Super Bit Mapping) function When you record through the ANALOG input, the SBM function enables you to record a 24bit high quality sound source by converting it to a 16-bit source without reduction in sound quality. This is made possible by incorporating a noise-shaping filter in the 24-bit A/D converter of this unit, which has a frequency range designed to cover the range of human hearing. When you press the button again, the function is canceled and the indicator turns off. Notes If "Smart Space" appears in the display (Smart Space Function) There has been an extended silence of 4 to 30 seconds in length during recording. When the signal is input again, the silence is replaced with a blank of about 3 seconds and the deck continues recording. Note that new track numbers may not be marked for portions recorded while this function is activated. Also, this function does not activate even if there has been an extended silence of 4 to 30 seconds in length when the deck started recording from the blank portion. To turn off the Smart Space Function and Auto Cut Function Set "Smart Space" in Setup Menu to "Off. " For details, see "Using the Setup Menu" (page 28). Note · You cannot change the setting while recording. · When you record through the DIGITAL OPTICAL IN input, or when you make Synchro-Recording, the SBM function is automatically canceled. When you turn off the Smart Space Function, the Auto Cut Function is also turned off automatically. 17 Synchro-Recording a CD to CD-R or CD-RW You can easily make digital recordings from a CD to a CD-R or CD-RW. Each recording type can be selected both in normal speed Synchro-Recording and High-Speed SynchroRecording (page 19). Normal Synchro-Recording (NORM SYNC) Notes · After recording, you must finalize the disc. Until the disc is properly finalized, it cannot be played on any other machine. · A CD text contained in the disc is not automatically recorded on the disc. To label tracks/discs, see "Labeling Tracks/Discs" (page 26). Tip · You cannot pause recording in Synchro-Recording. · If you start the recording when Shuffle play is set, Shuffle play is automatically canceled. · Smart Space, Auto Cut, and SBM functions do not work during Synchro-Recording. · The recording level is set to 0. 0 dB regardless of the Setup Menu setting. [. . . ] · You can record up to 99 tracks. Note C13/ Rec Error Recording has not been completed successfully because of vibration. · Relocate the unit in a place free of vibration and restart the recording again. The disc you try to record is excessively dirty (such as oilstained or finger marked) or scratched. · Replace the disc with another one and restart the recording again. When you turn on the unit, you will hear some mechanical noise from the unit. [. . . ]