User manual SONY MHC-RX55

[. . . ] To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the apparatus. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. Don't throw away the battery with general house waste, dispose of it correctly as chemical waste. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] --" appears when the total CD program time exceeds 100 minutes, or when you select a CD track whose number is 21 or over. You can then tune in any of those stations simply by selecting the corresponding preset number. Or + on the remote) until the frequency indication starts to change, then release it. Automatically preset all of the stations that can be received in your area Manually set the radio frequency of your favourite stations Scanning stops automatically when the system tunes in a station. If "TUNED" does not appear and the scanning does not stop Set the frequency of the desired radio station as described in steps 2 through 6 of "Setting presets through manual tuning". Tune in a station Follow the procedure described in with a weak "Setting presets through manual signal tuning". Set another station to an existing preset number Start over from step 1. Or > (or PRESET ­ or + on the remote) repeatedly to select the preset number you want to store the other station. To change the AM tuning interval, tune in any AM station first, then turn off the system. The preset stations are retained for half a day even if you disconnect the mains lead or if a power failure occurs. ⷠTo improve broadcast reception, reorient or move the supplied antenna near a window or outdoors. Press DISPLAY repeatedly while the system is off until the demonstration display or the clock display disappears. Each time you press the button, the display changes cyclically as follows: Elapsed playing time on the current track t Remaining time on the current track t Remaining time on the current CD t Clock display (for eight seconds) t Effect status Each time you press the button, the display switches cyclically as follows: Demonstration display t Clock display* t No display (Power Saving Mode) * The clock is displayed only if you set the clock. Each time you press the button, the display changes cyclically as follows: During normal play mode: Total number of tracks and total playing time t Clock display (for eight seconds) t Effect status During Program Play mode when there is a program: The last track number of the program and the total playing time t Total number of programed tracks (for five seconds) t Clock display (for eight seconds) t Effect status You need to connect a video game machine (see "Hooking up video game machine" on page 24). Falling asleep to music -- Sleep Timer You can set the system to turn off after a certain time, so that you can fall asleep to music. Each time you press the button, the minute display (the turn-off time) changes cyclically as follows: AUTO* t 90 MIN t 80 MIN t 70 MIN t . t 10 MIN t OFF * The system turns off when the current CD or tape finishes playback (for up to 100 minutes). Mixing video game sound with other sound source Each time you press the button, the level of the game sound changes cyclically as follows: MIXING LOW t MIXING MID t MIXING HIGH t MIXING OFF ** You cannot check the remaining time when you select "AUTO". ⷠOnce Game Mixing is activated, it will remain active while the power is on even if the source sound is changed. If you start recording while Game Mixing is activated, Game Mixing is canceled. To record the mixed sound, press GAME MIXING after step 4 of "Recording from a CD/tape/radio manually" on page 18, and then press REC PAUSE/START to start the recording. Make sure you have set the clock (see "Setting the clock" on page 10). [. . . ] Besides, the discs, which are not yet finalized at the end of recording, cannot be played back. The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off. ⷠUnplug the system from the wall outlet (mains) if it is not to be used for an extended period of time. Should any solid object or liquid fall into the component, unplug the system and have it checked by qualified personnel before operating it any further. [. . . ]