User manual SONY KDL-52NX800

[. . . ] If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. If you should lose the fuse cover, please contact your nearest Sony service station. Introduction Thank you for choosing this Sony product. Before operating the TV, please read this manual thoroughly and retain it for future reference. Trademark information · is a registered trademark of the DVB project. · "PlayStation" is a trademark of Sony Computer Entertainment, Inc. [. . . ] If you know the channel number, you can use the number buttons to directly select a channel. 3 Press OK. Channels that are stored in the Favourite list are indicated by a symbol. Turn off the Favourite list Move through in the Favourite list Display the previous or next five channels See brief details on current programmes Watch a channel Add or remove channels in the Favourite list Press . Press m/M. Press again to cancel. Press OK while selecting a channel. 1 Press the blue button. Channels that are stored in the Favourite list are indicated by a symbol. 2 Press m/M to select the channel you want to add or remove. If there are more than five channels in the list, press the green button for the next five channels or press the red button for the previous five channels. If you know the channel number, you can use the number buttons to directly select a channel. 3 4 Remove all channels from the Favourite list Press OK. Press the yellow button. A display appears to confirm that you want to delete all channels from the Favourite list. 1 2 3 Press < to select "Yes", then press OK to confirm. 18 Viewing pictures from connected equipment Switch on the connected equipment, then perform one of the following operation. For equipment connected to the scart sockets using a fully-wired 21-pin scart lead Start playback on the connected equipment. For an auto-tuned VCR page 11 Press PROG +/-, or the number buttons, to select the video channel. You can also press / repeatedly until the correct input symbol (see below) appears on the screen. For other connected equipment Press / repeatedly until the correct input symbol (see below) appears on the screen or press OK to access the Input signal index table. Press , to select Using the Menu Navigating through menus Using the Menu an input source, press m/M, then press OK. 1/ 1, 2/ 2: Audio/video or RGB input signal through the scart socket / 1 or 2. 3: Component input signal through the Y, PB/CB, PR/CR sockets / 3, and audio input signal through the L/G/S/I, R/D/D/D sockets / 3. 4/ 4: Video input signal through the video socket 4, and audio input signal through the audio socket L/G/S/I (MONO), R/D/D/D sockets 4. appears only if the equipment is connected to the S video socket 4 instead of the video socket 4, and S video input signal is input through the S video socket 4. Press </, to set the level, then press OK. Resets the "Treble, " "Bass" and "Balance" settings to the factory settings. 1 2 Press OK to select "Reset". Press m/M to select "OK, " then press OK. Continued 23 Dual Sound Selects the sound from the speaker for a stereo or bilingual broadcast. 1 2 Press OK to select "Dual Sound". Press m/M to select one of the following, then press OK. · Stereo/Mono: For a stereo broadcast. · A/B/Mono: For a bilingual broadcast, select "A" for sound channel 1, "B" for sound channel 2, or "Mono" for a mono channel, if available. Tip If you select other equipment connected to the TV, set "Dual Sound" to "Stereo, " "A" or "B. " Auto Volume Keeps a constant volume level even when volume level gaps occur (e. g. , adverts tend to be louder than programmes). 1 2 Press OK to select "Auto Volume". Press m/M to select "On, " then press OK. Tip If you set "Sound Effect" to "Dolby Virtual", "Auto Volume" will automatically be switched to "Off". 24 Screen menu Screen Auto Format: Screen Format: RGB Center On Smart 0 You can select the options listed below on the Screen Control menu. To select options, see "Navigating through menus" (page 19). Select: Set: OK Back: End: MENU Auto Format Automatically changes the screen format according to the broadcast signal. Using the Menu 1 2 Press OK to select "Auto Format". Press m/M to select "On, " then press OK. Tips · Even if you have selected "On" or "Off" in "Auto Format", you can always modify the format of the screen by pressing repeatedly. · "Auto Format" is available for PAL and SECAM signals only. Screen Format For details about the screen format, see (15). 1 2 RGB Center Press OK to select "Screen Format". Press m/M to select "Wide, " "Smart, " "4:3, " "14:9" or "Zoom" (see (15) for details), then press OK. Adjusts the horizontal picture position so that the picture is in the middle of the screen. 1 2 Press OK to select "RGB Center". Press </, to adjust the centre of the picture between -5 and +5, then press OK. Tip This option is only available if an RGB source has been connected to the Scarts connectors 2/ 2 on the rear of the TV. 1/ 1 or 25 Features menu Features AV2 Output TV Speakers PC Adjustment TV On You can select the options listed below on the Features menu. [. . . ] 1 Measure how long the 1 (standby) indicator flashes and stops flashing. For example, the indicator flashes for two seconds, stops flashing for one second, and flashes for two seconds. 2 Press 1 on the TV (Front side) to switch it off, disconnect the mains lead, and inform your dealer or Sony service centre of how the indicator flashes (duration and interval). When it is not flashing 1 Check the items in the tables below. 2 If the problem still persists, have your TV serviced by qualified service personnel. Picture Problem No picture (screen is dark) and no sound No picture or no menu information from equipment connected to the scart connector Distorted picture Cause/Remedy · Check the aerial connection. · Connect the TV to the mains, and press 1 on the TV (front side). · If the 1 (standby) indicator lights up in red, press TV "/1. [. . . ]