User manual SONY KDL-40L4000

[. . . ] LCD Digital Colour TV Operating Instructions KDL-52V4000/52V42xx KDL-46V4000/46V42xx KDL-40V4000/40V42xx KDL-40S40xx/40U40xx KDL-40L4000 U © 2008 Sony Corporation 3-298-969-12(1) NOTICE FOR CUSTOMERS IN THE UNITED KINGDOM A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience. Should the fuse in the plug supplied need to be replaced with the same rating of fuse approved by ASTA or BSI to BS 1362 (i. e. , marked with or ) must be used. When an alternative type of plug is used it should be fitted with the same rating of fuse, otherwise the circuit should be protected by a 13 AMP FUSE at the distribution board. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. [. . . ] Connect a PC (page 21), and make sure that images from the PC appear on the screen. In analogue mode, press PROG +/­ or the number buttons, to select the video channel. For other connected equipment ~ · "Power Management" (page 29) is not available in PIP mode. Using Optional Equipment Press to display a list of connected equipment. The highlighted item is automatically selected if you do not perform any operation for two seconds after pressing F/f. If you have set an input source to "Skip" in the "AV Preset" menu (page 30), that input source does not appear in the list. z · To return to normal TV mode, press DIGITAL or ANALOG. 1 Press TOOLS. 2 Press F/f to select "PIP", then press . The picture from the connected PC is displayed in full size, and the TV programme is displayed in the small screen. You can use F/f/G/g to change the position of the TV programme screen. 3 Press the number buttons or PROG +/­ to select a TV channel. To return to single picture mode To view two pictures simultaneously ­ PAP (Picture and Picture) You can view two pictures (external input and TV programme) on the screen simultaneously. Connect an optional equipment (page 21), and make sure that images from the equipment appear on the screen (page 23). Press RETURN. z · You can switch the audible picture by selecting "Audio Swap" from the Tools menu. ~ · This function is not available for a PC input source. · The analogue TV video in the TV programme picture will not appear while displaying AV1, AV2 or AV3 in the external input picture. However, you can hear the analogue video's sound. 1 Press TOOLS. 2 Press F/f to select "PAP", then press . The picture from the connected equipment is displayed on the left, and the TV programme is displayed on the right. 23 GB To make the control for HDMI settings Using BRAVIA Sync (Control for HDMI) The control for HDMI function enables the TV to communicate with the connected equipment that is compatible with the function, using HDMI CEC (Consumer Electronics Control). For example, by connecting Sony equipment that is compatible with control for HDMI (with HDMI cables), you can control them together. Be sure to connect the equipment correctly, and make the necessary settings. Control for HDMI · Automatically turns the connected equipment off when you switch the TV to standby mode using the remote. · Automatically turns the TV on and switches the input to the connected equipment when the equipment starts to play. · If you turn on a connected audio system while the TV is on, the sound output switches from the TV speaker to the audio system. · Adjusts the volume (2 +/­) and mutes the sound (%) of a connected audio system. · You can operate the connected Sony equipment that has the BRAVIA Sync logo by the TV remote by pressing: ­ N/x/X/m/M to operate the connected equipment directly. ­ SYNC MENU to display the menu of the connected HDMI equipment on the screen. After displaying the menu, you can operate the menu screen by using F/f/G/g and . ­ TOOLS to display "Device Control", then select options from "Menu", "Options", and "Content List" to operate the equipment. ­ Refer to the instruction manual of the equipment for available control. The control for HDMI settings must be set on both the TV side and connected equipment side. For settings on the connected equipment, refer to the operating instructions for that equipment. To connect the equipment that is compatible with control for HDMI Connect the compatible equipment and the TV with an HDMI cable. When connecting an audio system, be sure to also connect the DIGITAL AUDIO (PCM) OUT (OPTICAL) socket of the TV and the audio system using an optical audio cable (except for KDL40S40xx/40U40xx/40L4000). [. . . ] PC input signal reference chart for HDMI IN 1, 2, 3* Resolution Signals VGA SVGA XGA WXGA WXGA SXGA Horizontal (Pixel) 640 800 1024 1280 1280 1280 × Vertical (Line) × 480 × 600 × 768 × 768 × 768 × 1024 Horizontal frequency (kHz) 31. 5 37. 9 48. 4 47. 4 47. 8 64. 0 Vertical frequency (Hz) 60 60 60 60 60 60 Standard VESA VESA Guidelines VESA Guidelines VESA VESA VESA * HDMI IN 3 is not available in KDL-40L4000. 36 GB Troubleshooting Check whether the 1 (standby) indicator is flashing in red. When the 1 (standby) indicator is flashing The self-diagnosis function is activated. 1 Count how many times the 1 (standby) indicator flashes between each two second break. For example, the indicator may flash three times, go off for two seconds, then flash again three times. 2 Press 1 on the TV to turn it off, disconnect the mains lead, and inform your dealer or Sony service centre of how the indicator flashes (number of flashes). When the 1 (standby) indicator is not flashing 1 Check the items in the tables below. 2 If the problem persists, have your TV serviced by qualified service personnel. Condition Explanation/Solution Picture There is no picture (screen is dark) and no sound. No picture or menu information from equipment connected to the scart connector appears on the screen. · If the 1 (standby) indicator lights up in red, press "/1. [. . . ]