User manual SONY ICD-B5

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SONY ICD-B5. We hope that this SONY ICD-B5 user guide will be useful to you.


SONY ICD-B5 : Download the complete user guide (575 Ko)

You may also download the following manuals related to this product:

   SONY ICD-B5 (606 ko)
   SONY ICD-B5 (606 ko)
   SONY ICD-B5 (597 ko)
   SONY ICD-B5 (600 ko)
   SONY ICD-B5 (604 ko)
   SONY ICD-B5 (599 ko)
   SONY ICD-B5 (605 ko)
   SONY ICD-B5 annexe 1 (619 ko)
   SONY ICD-B5 annexe 1 (620 ko)
   SONY ICD-B5 annexe 1 (651 ko)
   SONY ICD-B5 annexe 2 (664 ko)
   SONY ICD-B5 annexe 1 (650 ko)
   SONY ICD-B5 annexe 2 (666 ko)
   SONY ICD-B5 annexe 1 (644 ko)
   SONY ICD-B5 annexe 1 (648 ko)
   SONY ICD-B5 annexe 1 (646 ko)
   SONY ICD-B5 (571 ko)
   SONY ICD-B5 (606 ko)
   SONY ICD-B5 annexe 2 (575 ko)
   SONY ICD-B5 annexe 1 (650 ko)
   SONY ICD-B5 annexe 3 (571 ko)
   SONY ICD-B5 DATASHEET (466 ko)

Manual abstract: user guide SONY ICD-B5

Detailed instructions for use are in the User's Guide.

[. . . ] 3-242-997-11 (1) BGetting started BBasic Operations IC Recorder Operating Instructions Owner's Record The model number is located at the rear and the serial number is located inside the battery compartment. Refer to these numbers whenever you call upon your Sony dealer regarding this product. ICD-B5 Serial No. Step 1: Installing the Batteries Recording Messages Replacing the batteries The battery indicator on the display window shows the battery condition. When flashes, the batteries are exhausted and the unit will stop operation. [. . . ] After about one hour, the unit goes into the stop mode at the current position. You cannot record messages up to the maximum recording time (150 minutes). · No more recording can be made when 99 messages each have been recorded in both A and B folders. · Due to the limitation of the IC recording system, this unit records in the minimum recording unit of approx. If the length of each message cannot be divided by the minimum recording unit, the remaining recording time may decrease by more than the total length of the messages. 3 Set the time. 3 Set the minute. 1 Press ­ . or >+ to select the digits of the hour. The unit does not operate correctly. · Take out the battery and insert it again. Please note that recorded messages may be erased during service or repair work. The minute digits will flash. Backup recommendations To avoid potential risk of data loss caused by accidental operation or malfunction of the IC recorder, we recommend that you save a backup copy of your recorded messages on a tape recorder, etc. 4 Press NxPLAY/STOP at the time signal. The display will return to "SET DATE". 5 Press MENU to exit from the menu mode. 1 Tip This unit does not have a power on/off switch. The display is shown at all times. Erasing Messages You can erase the recorded messages one by one or all messages in a folder at a time. Note that once a recording has been erased, you cannot retrieve it. BVarious Ways of Recording BOther Functions Adding a Recording to a Previously Recorded Message You can add a recording to the message being played back. The added recording will be placed after the current message and counted as a part of the message. During playback of Message 3 Dividing a Message into Two/ Combining Messages -- Index Function You can divide a message by adding an index, or combine messages by erasing the index. While recording/playing back messages, you can add an index (see below). In stop mode, you can erase the index. Moving Messages to a Different Folder -- Move Function You can move the recorded messages to another folder. Example: Moving Message 3 in Folder A to Folder B 4 Press NxPLAY/STOP. The hour digits will flash. Selecting the Display Mode You can select the display mode for the stop, recording and playback modes. (If the unit is left unoperated for more than 3 seconds in the stop mode, the display will show the current time, regardless of the display mode setting. ) Each time you press DISPLAY, the display mode will change as shown below: Playing Back All Messages in a Folder Continuously CONT ON: You can play back all messages in a folder continuously. CONT OFF: Playback stops at the end of each message. 5 Set the alarm time. 1 Press ­ . The minute digits will flash. 1 2 Play back the message you want to move. 1 Erasing messages one by one When a message is erased, the remaining messages will advance and renumbered so that there will be no space between messages. Before erasing Message 1 Message 2 Message 3 Message 4 Message 5 Press MENU to enter the menu mode. Message 3 Message 4 Dividing a Message by Adding an Index You can add an index to a message during recording or playback. By dividing a message, you can easily find the point you want to play back when you make a long recording such as a meeting. Before adding an index After adding an index Message 1 Message 2 Message 3 Erase Message 3 After erasing Message 1 Message 2 Message 3 Message 4 After adding a recording Message 3 Message 4 Added recording Meeting at 2 o'clock on December 1. at Conference room A While playing back the message, press FOLDER to flash the indication of the folder to which you want to move the message (B in this case). The first and last 5 seconds of the message will be played back 10 times, while the folder indication and "MOVE" flash. , 2 Press ­ . "ALARM ON" and ", " will be displayed to indicate that the setting has been completed. Counter: Elapsed playback/recording time in one message m Remaining recording time: 2 Press ­ . [. . . ] or >+ to display the message number as the divided messages each have message numbers. Press MENU to exit the menu mode. 2 Press NxPLAY/STOP. "OFF" starts to flash. To play the divided messages continuously EAR, EARPHONE, v or REC OUT Select "ON" for "CONT" as described in "Playing Back All Messages in a Folder Continuously. " Notes · If 99 messages have been recorded in a folder, you cannot add an index. In that case, reduce the number of messages to 98 or less by erasing unnecessary messages or by moving some of the messages to another folder before adding an index. · If you add an index to a message with an alarm setting, the alarm setting remains only with the former message divided. What beep sound means 3 Press ­ . [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SONY ICD-B5




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SONY ICD-B5 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.