User manual SONY AIR-SA-10

[. . . ] Do not place the naked flame sources such as lighted candles on the apparatus. To reduce the risk of fire or electric shock, do not expose this apparatus to dripping or splashing, and do not place objects filled with liquids, such as vases, on the apparatus. As the main plug is used to disconnect the unit from the mains, connect the unit to an easily accessible AC outlet. Should you notice an abnormality in the unit, disconnect the main plug from the AC outlet immediately. [. . . ] However, if a neighbor has an S-AIR main unit with the same S-AIR ID as your S-AIR main unit, you may be able to hear the audio transmitted from your neighbor's S-AIR main unit on your system. To prevent this, you can identify the unit with a specific S-AIR main unit by performing the pairing operation. When you perform pairing Recent times have seen the rapid spread of DVD media, Digital Broadcasting, and other high-quality media. To ensure that the subtle nuances of these highquality media are transmitted with no deterioration, Sony has developed a technology called "S-AIR" for the radio transmission of digital audio signals with no compression, and has incorporated this technology into the EZW-RT10. This technology transfers digital audio signals with no compression using the 2. 4 GHz band range of ISM band (Industrial, Scientific, and Medical band), such as wireless LANs and Bluetooth applications. Before pairing, the connection is established by the SAIR ID (example). Your system Neighboring system This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This unit ID A CAUTION ID A S-AIR main unit ID A S-AIR main unit Owner's Record The model and serial numbers are located on the bottom of the unit. Refer to them whenever you call upon your Sony dealer regarding this product. Serial No. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. For the wireless transceiver (EZW-RT10) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The connection is established between the paired unit and S-AIR main unit. Your system Neighboring system Important Safety Instructions 1) 2) 3) 4) 5) 6) 7) Read these instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding-type plug. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11) Only use attachments/accessories specified by the manufacturer. This unit ID A This equipment must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. This equipment should be installed and operated with at least 20cm and more between the radiator and person's body (excluding extremities: hands, wrists, feet and ankles). Pairing ID A S-AIR main unit ID A S-AIR main unit 1 Check that the power of the unit and the S-AIR main unit to be connected are turned on. If the issue persists, contact your nearest Sony dealer. (stereo mini jack): Accepts headphones with an impedance of 8 ohms or more Speaker section Speaker system: Full range, bass-reflex type Speaker units: 65 mm, cone type (2) Nominal impedance: 3 ohms Connecting the unit and S-AIR main unit is not possible. (The S-AIR indicator flashes. ) Wireless transceiver (EZW-RT10) Setting the clock 1 Turn on the unit. Press . Changing the display To change the information on the display while the unit is on Press DISPLAY . Each time you press the button, the display changes as follows: When the unit is connected to an S-AIR main unit: 6 Press / repeatedly to select the desired option. When no sound is output from the S-AIR main unit or the audio signal level is too low. When the S-AIR main unit is not ready for playback at the set start time. Note that the alarm continues to sound even if the S-AIR main unit becomes ready after the start time has passed. However, sound from the S-AIR main unit is not output in the following cases. [. . . ] Stop using any equipment that generates electromagnetic energy such as a microwave oven. Place so that the unit and the S-AIR main unit are separated from other wireless devices. Do not place a mobile phone near the unit, as this may result in noise. then press CLOCK/TIMER ENTER . "ON TIME" appears, and the hour indication flashes. 2 Press CLOCK/TIMER ENTER . [. . . ]