User manual SONANCE ORIGINAL SERIES MEDIUM ROUND SPEAKERS INSTALLATION

[. . . ] · The main listening position should be between 4 and 10 feet (1. 2­3 m) away from the speakers. · If necessary, pivot the tweeter and the woofer of each speaker towards the listening position to maximize the soundstage. The pivoting feature is available only on the Original Series Medium Round 625R, 624R, 623R, 622R, and 621R speakers. The adjustable three-position tweeter switch is available on the 625R, 624R, 623R, and 623R TL. [. . . ] if the speaker is reMoved froM the Mounting hole, use the fastMount tabs will disConneCt and reMain inside the walls. Before Installation: Retrofit 1. Determine the location for the speaker (see Speaker Placement on page 1). Perform an obstruction survey to be certain that there are no studs, conduit, pipes, heating ducts or air returns that will interfere with the speaker. Mounting space requirements: · Medium Round speakers: 8¼" (210mm) diameter cut-out; 4¾" (121mm) depth within the mounting cavity. · Medium Round ThinLine ® speakers: 8¼" (210mm) diameter cut-out; 3 1/32" (77mm) depth within the mounting cavity. Position the included cutout template where the speaker is to be located and pencil an outline on the ceiling. · If you are unsure about obstructions, drill a small hole in the center of the outline and insert a coat hanger wire into the hole to feel-around for possible obstructions. Cut the mounting hole using a keyhole or drywall saw, and run the speaker wires from the mounting hole to the amplifier location. 6. The Roto-Lock clamps will automatically rotate into position and begin clamping the speaker (see Figure 4). · When you notice resistance on the screws the speaker has been clamped successfully. Figure 4: Original Series Medium Round Speaker Installation importaNt: always tighten. use low-torque settings. never over- Note: Consult loCal building Codes before running speaker wires through Ceilings. Installation Sonance Original Series Medium Round speakers feature exclusive FastMount tabs and an integral Roto-Lock ® mounting system for quick mounting directly into existing ceilings and walls. Note: adjusting the tension of the roto-loCk ClaMps so that the speaker fraMe is flat will help ensure that the grille ContaCts the Ceiling all the way around the speaker for a proper fit. 7. Insert about half of the grille into the groove at the edge of the speaker. Gently fit the remaining half of the grille by working around the speaker, fitting the grille into the groove as you go. · You can adjust the torque to the Roto-Lock screws to achieve a proper grille fit. WarNiNg: the edges of the fastMount tabs are very sharp. use Caution when handling the speaker. 1. Run speaker wire from each speaker to the amplifier location. 3 ORIGINALSERIESMEDIUMROUNDSPEAKERS Painting the Speakers and Grilles All Sonance Original Series Medium speakers come from the factory fitted with a plastic "paint plug. " Use the paint plug to protect the speaker drivers while the flange is being painted along with the wall. You can paint the speakers and grilles before installing them, which will eliminate the "paint scar" if the speaker ever needs to be removed for service. You can also paint the speakers after installation, but before the grilles are attached. Sonance always suggests painting the grille separately from the speaker. It is held in place with a light tacking glue that makes it easy to remove. Spray the grilles with thinned paint (5 parts thinner to 1 part paint), being careful not to plug the holes. Too heavy a coat of paint on the grille will adversely affect the sound of the speaker. Once the grilles and flange are painted and dry, replace the under-grille cloth, remove the paint plug from the speaker flange and install the grille. To pivot the woofer: 1. Apply pressure on the outer edge of the tweeter support bracket, as shown below in Figure 5. [. . . ] IN ANY EVENT, SONANCE SHALL NOT BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL, ECONOMIC, PROPERTY, BODILY INJURY, OR PERSONAL INJURY DAMAGES ARISING FROM THE PRODUCT, ANY BREACH OF THIS WARRANTY OR OTHERWISE. This warranty statement gives you specific legal rights, and you may have other rights which vary from state to state. Some states do not allow the exclusion of implied warranties or limitations of remedies, so the above exclusions and limitations may not apply. If your state does not allow disclaimer of implied warranties, the duration of such implied warranties is limited to period of Sonance's express warranty. your Product model and description: Original Series medium round Speaker Additional Limitations and Exclusions from Warranty Coverage: The warranty described above is non-transferable, applies only to the initial installation of the Product, does not include installation of any repaired or replaced Product, does not include damage to allied or associated equipment which may result for any reason from use with this Product, and does not include labor or parts caused by accident, disaster, negligence, improper installation, misuse (e. g. [. . . ]