User manual SOCKET GA-8IG1000MK

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X/8X (1. 5V) notch"(show below), please make sure your AGP card is AGP 4X/8X (1. 5V). AGP 4X/8X notch Caution: AGP 2X card is not supported by Intel® 845(GE/PE) / 845(E/G) / 850(E) / E7205 / 865(G/PE/P) / 875P. Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. It can be switched between AGP 2X(3. 3V) or 4X(1. 5V) mode by adjusting the jumper. [. . . ] (Default value) USB Mouse Support Enabled Disabled Enable USB Mouse Support. (Default value) AC97 Audio Auto Disabled Auto detect AC'97 audio function. (Default Value) Disable AC'97 audio function. Onboard H/W LAN Enabled Disabled Enable Onboard H/W LAN function. (Default value) Disable this function. Onboard Serial Port 1 Auto 3F8/IRQ4 2F8/IRQ3 3E8/IRQ4 2E8/IRQ3 Disabled BIOS will automatically setup the port 1 address. Disable onboard Serial port 1. - 43 - BIOS Setup English Onboard Serial Port 2 Auto 3F8/IRQ4 2F8/IRQ3 3E8/IRQ4 2E8/IRQ3 Disabled BIOS will automatically setup the port 2 address. Disable onboard Serial port 2. UART Mode Select This item allows you to determine which Infra Red(IR) function of Onboard I/O chip. Set onboard I/O chip UART to SCR Interface. UR2Duplex Mode This feature allows you to seclect IR mode. This function will available when "UART Mode Select" doesn't set at Normal/SCR. (Default Value) IR Function Duplex Full. Onboard Parallel port This feature allows you to select from a given set of parameters if the parallel port uses the onboard I/O controller. Enable onboard LPT port and address is 3BC/IRQ7. GA-8IG1000MK Motherboard - 44 - Parallel Port Mode This feature allows you to connect with an advanced printer via the port mode it supports. Using Parallel port as ECP & EPP mode. English ECP Mode UseDMA This feature allows you to select Direct Memory Access(DMA) channel if the ECP mode selected. This function will available when "Parallel Port Mode" set at ECP or ECP+EPP. (Default Value) Set ECP Mode Use DMA to 1. Game Port Address 201 209 Disabled Set Game Port Address to 201. Disable this function. Midi Port Address 300 330 Disabled Set Midi Port Address to 300. (Default Value) Disable this function. Midi Port IRQ 5 10 Set Midi Port IRQ to 5. (Default Value) - 45 - BIOS Setup English Power Management Setup CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Power Management Setup ACPI Suspend Type Power LED in S1 state Off by Power button PME Event Wake Up ModemRingOn/WakeOnLan Resume by Alarm x Date (of Month) Alarm x Time (hh:mm:ss) Alarm Power On by Mouse Power On by Keyboard x KB Power ON Password AC Back Function [S1(POS)] [Blinking] [Instant-off] [Enabled] [Enabled] [Disabled] Everyday 0:0:0 [Disabled] [Disabled] Enter [Soft-Off] [S3] Set suspend type to Suspend to RAM under ACPI OS Item Help Menu Level [S1] Set suspend type to Power On Suspend under ACPI OS : Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 5: Power Management Setup ACPI Suspend Type S1(POS) S3(STR) Set ACPI suspend type to S1. (Default Value) Set ACPI suspend type to S3. Power LED in S1 state Blinking Dual/OFF In standby mode(S1), power LED will blink. If use dual color LED, power LED will turn to another color. GA-8IG1000MK Motherboard - 46 - Off by Power button Instant-off Delay 4 Sec. Enter suspend if button is pressed less than 4 sec. English PME Event Wake Up Disabled Enabled Disable this function. (Default Value) ModemRingOn/WakeOnLAN An incoming call via modem can awake the system from any suspend state or an input signal comes from the other client server on the LAN can awake the system from any suspend state. (Default Value) Resume by Alarm You can set "Resume by Alarm" item to enabled and key in Data/time to power on system. Date (of Month) Alarm : Everyday, 1~31 Time (hh: mm: ss) Alarm : (0~23) : (0~59) : (0~59) Power On By Mouse Disabled Mouse Click Disabled this function. [. . . ] Support(Sales/Marketing) : http://ggts. gigabyte. com. tw/nontech. asp WEB address (English): http://www. gigabyte. com. tw WEB address (Chinese): http://chinese. giga-byte. com U. S. A. Support : http://www. giga-byte. com/TechSupport/ServiceCenter. htm Non-Tech. Support(Sales/Marketing) : http://ggts. gigabyte. com. tw/nontech. asp WEB address : http://www. giga-byte. com Germany G. B. T. TECHNOLOGY TRADING GMBH Address: Friedrich-Ebert-Damm 112 22047 Hamburg Deutschland TEL: +49-40-2533040 (Sales) +49-1803-428468 (Tech. ) FAX: +49-40-25492343 (Sales) +49-1803-428329 (Tech. ) Tech. [. . . ]