User manual SMITH CORONA OFFICE2000CHAP3

[. . . ] Code + or Spacebar -- Moves typing position to the right one character at a time. Code + -- Moves typing position down equal to line setting (i. e. , if you are double spacing text, key moves typing position down two lines. ) Code + -- Moves typing position up equal to your line setting (i. e. , if you are single spacing text, key moves typing position up one line. ) NOTE: The / are repeating keys. If they are held down, the paper will continue to move up or down. Smith Corona Corporation Type Mode -- 3-1 Auto Return Code + !^ 1 You can program the Memory Typewriter to automatically return at the end of each line. When a space or hyphen is typed in the "warning zone, " which begins five spaces before the right margin, the carrier automatically returns to the next line. [. . . ] Display prompts: Indent OFF. Code + ¢~ 6 Smith Corona Corporation Type Mode -- 3-5 Changing Settings You can change the end of page setting, line spacing, impression control, pitch and number of lines displayed in Type Mode. (See "Page Layout. ") NOTE: If you change pitch, remember to change the printwheel. Corrections The typewriter can automatically correct all characters in a three line correction memory buffer. You can easily correct characters not in the buffer by performing an extra step (see "Off-Line Correction"). Remember to use Code + , Code + , Code + , Code + , Return, Back Space, and Spacebar when positioning the print hammer to make a correction. IMPORTANT: If you changed printwheels, be sure to insert the proper printwheel before making corrections. Position Print Hammer Erasing Character(s) in Correction Memory 1. Position the print hammer on the incorrect character, if necessary, and then press Correct. Be sure to activate Bold or Underscore if you want the replacement text enhanced. Press Code + Reloc (Return) to quickly return to your previous typing position, if necessary. NOTE: You erase the correction memory buffer when you turn off the typewriter, use the Automatic Paper Insert feature, switch modes, or change pitch. Correct 2. Type Correction 3. Code + Return Reloc WordEraser ® Position Print Hammer This feature allows you to erase word(s) within the correction memory buffer. Position the print hammer on any character in the incorrect word or on the space to the right of the word. If you are correcting more than one word, position the print hammer on the right-most incorrect word. Be sure to activate Bold or Underscore if you want the replacement text enhanced. Press Code + Reloc (Return) to return to your previous typing position, if necessary. Smith Corona Corporation ® WordEraser LineEraser Type Correction 2. Code + Return 3. 4. Reloc 3-6 -- Type Mode LineEraser ® Using the LineEraser feature, you can easily remove an entire line of text located in correction memory. Correction begins immediately from the last character typed on the line up to the first character typed on the line. Be sure to activate Bold or Underscore if you want to replace enhanced text. Press Code + Reloc (Return) to return to your previous typing position, if necessary. NOTE: If Code + LineEraser is pressed while off-line or when there is no text in the correction buffer, you will receive an ERROR message. Position Print Hammer Code + ® WordEraser LineEraser Type Correction Code + Return Reloc Character Swap ® Character Swap allows you to reverse the order of adjacent characters on a line within the correction memory buffer. For example, if you typed " Teh, " you could reverse the " h" and the "e , " to produce " The. " Character Swap will transpose lower-case and upper-case letters without changing the case. [. . . ] Press Code + Reloc (Return) to quickly return to your previous typing position. NOTE: For bold characters, repeat the correction process, if necessary. Code + Correct Retype the Incorrect Character to Erase the Error 2. Type Correction Code + Return Reloc 3-8 -- Type Mode Smith Corona Corporation Forward Correction To correct several characters or word(s) not in the correction memory buffer. Position the print hammer to the first character in the series to be corrected using Code + , Code + , Code + , Code + , Spacebar, Return, and Back Space. You may have to adjust your typing speed so that the typewriter removes characters correctly. ) Press Code + Correct. [. . . ]