User manual SIRONA INLAB 3D

[. . . ] áåi~Ä Pa léÉê~íçêÛë=j~åì~ä sÉêëáçå=OKSu båÖäáëÜ Copyright © Sirona Dental Systems GmbH 2003. All rights reserved. The information contained in this manual cannot be changed without special notification. The software and all related documentation are protected by copyright. You must therefore handle it in the same way as any other protected material. [. . . ] Re-insert the partially milled block into the milling unit and continue the milling process. 114 59 76 571 D 3344 D 3344. 208. 06. 03. 02 03. 2005 6. 7 Fast milling 6. 7 Fast milling CAUTION Loss of quality!Fast milling may have a negative influence on the quality of the restoration!If desired, the milling process can be accelerated for the materials listed below. To do this, simply set a check mark in the corresponding check box of the block selection dialog box. n VITA Mark II n VITA Esthetic Line n VITA TriLuxe n IVOCLAR ProCAD Fig. 6-12 Block selection n IVOCLAR ProCAD [Top Touch] n 3M Paradigm This mode is faster, however the surface of the milled restoration is slightly rougher. 59 76 571 D 3344 D 3344. 208. 06. 03. 02 03. 2005 115 7 Managing/archiving data 7 Managing/archiving data To create an archive of all finished restorations you should save regularly. Three different options can be independently activated and deactivated under Settings / Configuration / Save (see , , Configuration: Save" on page 62). Saving regularly Compress files If this option is activated, a single compressed restoration file will be created in each tooth folder (recommended!). If it is deactivated, all of the images (optical impressions, height images, restoration images) and a line file will be saved to the hard disk as separate files. Create TIF file If this option is activated, the optical impression of the preparation will also be saved as a TIF image. Files in this format can be opened in conventional graphic applications. Connect database If a SIRONA database is installed in your system, it can be used for data archiving and patient management after selecting this option. Once the database has been connected, all patients stored in the database are known to the application. If the database connection is used, all CEREC restorations will be saved to the CEREC subfolder in the Pdata folder of the database. This folder is usually located on a server which can be accessed from all PCs connected to the network. With a database connection, CEREC restorations are also visible in S(V)IDEXIS when the All image filter is set. The image is then a representative image of the restoration (usually the optical impression of the preparation) in TIF format. CEREC images are assigned the image code VC (Video CEREC) in the SIRONA database. 116 59 76 571 D 3344 D 3344. 208. 06. 03. 02 03. 2005 7 Managing/archiving data Database import After the database connection is activated, all locally saved patients and restorations are transferred (imported) to the SIRONA database. A message indicating the successful database import is then displayed. Patients (and their restorations) cannot be imported to the SIRONA database if they are identified only by a card index number in the local CEREC data structure. A message informs the user about this situation during database import. Fig. 7-1 Database import Database export When the database connection is deactivated, a dialog box appears in which you can select whether the CEREC restorations stored in the database should be copied (exported) to the local CEREC data structure. The patient information will in any case be transferred by creating a patient folder in the CEREC data structure for each patient in the database. A message indicating the successful database export is then displayed. Fig. 7-2 Database export Restoration files Assuming that you have installed the program under Program Files / CEREC, the folder Program Files / CEREC / Data contains a subfolder for each patient bearing the patient name. Each patient folder contains one or more tooth folders in which the individual restoration files are stored. [. . . ] Uninstallation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17, 50 47 14 18 V Veneer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 Veneer thickness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18, 144, 145, 210 View window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]