User manual SIMRAD SL30 REV 2

[. . . ] SL 30/35 HULL SONAR OPERATORS MANUAL 974-25007001 Issue 2. 0 September 2003 SL 30/35 Hull Sonar Operators Manual List of Contents 974-25007001/2. 0 Page 1 Kongsberg Simrad Mesotech Ltd Products Warranty Policy Effective January 1, 2003 Kongsberg Simrad Mesotech Ltd. Warrants each new product (equipment) to be free of defects caused by faulty materials or poor workmanship for a period of twelve (12) months for underwater equipment and twenty-four (24) months for surface equipment from date of installation by an authorized Kongsberg Group Company, Simrad Distributor, Dealer or Agency. The warranty does not apply to defects caused by, force majeure events or misuse, including water damage to the surface equipment, improper maintenance and installation, including excessive wear and tear for which Kongsberg Simrad Mesotech Ltd. Is not responsible. Underwater Equipment: · Warranty for Underwater Equipment that is hull mounted, such as those mentioned below, will be assessed on a case-by-case basis but shall generally not be covered by the warranty: · · Hull Units, Sonar Dome Assemblies and Echo Sounder Transducers Transducer Units, Speed, Temperature and Depth Sensors Note: Additional expenses connected with replacement of transducers, such as dry- docking and diving, are not covered by this warranty. Warranty on Parts or Equipment Replacement: · · · It is at the sole discretion of Kongsberg Simrad Mesotech Ltd. [. . . ] The option can usually be set to On due to negligible effect of the loss in color depth. The Pulse Length control can be used to set the desired transmit pulse length on heads that support this feature. Generally, a shorter pulse length will give a sharper image but with reduced range. By default, the system adjusts the pulse length at different range and display mode settings according to the selection of the Optimize resolution or Maximize Range. The automatic selection of the pulse length can be disabled by clicking the Manual Setup box. Bandwidth is used to adjust the analog bandwidth of the received signal. An Analog Interface Module (AIM) is required to be able to run an analog telemetry sonar head with this system. Port Coquitlam, BC - Canada SL 30/35 Hull Sonar Operators Manual Menu and Software Description 974-25007001/2. 0 Page 4. 55 Narrow, Medium, Wide and Automatic. If the Automatic option is selected, then the system selects the optimal bandwidth depending on the current value of the pulse length. Note that the narrower the bandwidth, the less signal is fed through which results in a less noisy image. Transducer option is only available for heads equipped with remote switch able Fan-Cone transducer. It changes the active beam shape between a conical (symmetrical) and Fan (Asymmetrical in orthogonal direction). The Transmitter control is used to select the transmitter source for heads that are equipped with a remote control transmitter switch. In the case of an altimeter (1007 Echo sounder), the Options are Off (listen only), On, or Test (calibrated test tone for factory testing). For the new 1071 based analog sonar heads, the Test tone is automatically selected if the transmitter is turned off in low Power mode. For normal operation of the sonar head, the transmitter should always be left On. The Panel Gain control is used to adjust the overall gain for the image from this head. The Acquisition Resolution control is used to change the number of samples collected from the sonar head to twice its normal value. The data is acquired and recorded in high resolution but not necessarily displayed in high resolution. To display the data in high resolution, the display resolution must be set to High on the image control bar (see the Control Panel). Note that the screen resolution must be able to support a minimum of 960x960 pixels, otherwise the system automatically displays the sonar data in low resolution, even if collected in high acquisition resolution. 4. 59. 6. 3 Head Settings: Info This page shows the calibration results as well as some hardware information about the sonar head. Kongsberg Simrad Mesotech Ltd. Port Coquitlam, BC - Canada 974-25007001/2. 0 Page 4. 56 SL 30/35 Hull Sonar Operators Manual Menu and Software Description The Calibration results reflect the positional accuracy of the optical sensors in the rotary scanning heads. [. . . ] Port Coquitlam, BC - Canada SL 30/35 Hull Sonar Surface Processor Setup Instructions 901-10111802 / Issue 1. 4 Page 8 6. 4. Press the "Properties. . . " button. Select the "Location" page and set it up as shown. 6. 5. Go to the "Security" page and select "Use custom access permissions", "Use custom launch permissions" and "Use custom configuration permissions" options as shown. Kongsberg Mesotech Ltd. Port Coquitlam, BC - Canada SL 30/35 Hull Sonar Surface Processor Setup Instructions 901-10111802 / Issue 1. 4 Page 9 6. 6. Press "Edit. . . " button in "Use custom access permissions" to modify the permissions for that option. If the text "Everyone" does not appear as shown bellow, then press the "Add" button. 6. 7. Pressing the "Add" button will pop up the "Add Users and Groups" dialog box as follows. 6. 8. 6. 9. [. . . ]