User manual SIMRAD RD 301
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SIMRAD RD 301. We hope that this SIMRAD RD 301 user guide will be useful to you.
Manual abstract: user guide SIMRAD RD 301
Detailed instructions for use are in the User's Guide.
[. . . ] R D 3 0 1 U s er m an u al
Instruction manual
Remote display RD301
Digital depth repeater
RD301 U s e r ma nua l
INTRODUCTION
The RD301 remote display is made for use with the EA400/ EA600 and the EN 250 navigation echo sounder. It may also be used with other echo sounders, if they have NMEA0183 output. [. . . ] - The Auto selection switches between Forward, Backward and Unknown depending on the NMEA messages available. The led for positions will shift automatically and blink every third second, indicating that the Auto selection is active. If the transducer position is unknown, both leds will be on and blinking.
1 857-164821aa
R D 3 0 1 U s er m an u al
NMEA Input
1. Accepted messages (NMEA0183, version 2. 30), talker identifier is not processed: - Depth &Draught SDDPT, xxxx. x, xxxx. x, xxxx. x <Cr><Lf> $PSKPDPT, x. x, x. x, x. x, xx, xx, c-c*hh<CR><LF> (used by EA400 and EA600) Transducer location * Echo sounder channel number (0-99) - Depth below transducer Bottom echo strength (0, 9) Maximum range scale in use, meters SDDBT , xxxx. x, f, xxxx. x, M, xxx. x, F) Offset from transducer, meters Water depth relative to transducer, meters - Depth below transducer by EN 250 proprietary sentence shown to the left * Text string, indicating transducer position: FWD/AFT/PORT/STB. (only for EN 250)
(Cd7019)
PANEL MOUNTING
A Make a cut out in the Panel (5): 125 x 125 mm. C Unscrew the 4 screws in the frame (3) (one in each corner) and remove the frame. D Put the Monitor (4) in the cut out and mark the 4 centerpoints for the drill in the Panel (1)(2). Make sure that the screw heads correspond with the cut outs in the frame. Before fixing the monitor (4) in the cut out area in console (1)(2), apply sufficient amount of water sealant compound between the monitor (4) and console (1)(2). Before the frame (3) is remounted, apply sufficient amount of water sealant compound in the inner area of the frame and on the edges of the monitor (4), to ensure that water can not penetrate into the monitor (4). The front panel of the monitor is waterproof.
144 [5, 669]
Mounting bracket
62(2. 441) 13(0. 492)
1
Washer DIN 6797 (2x) Nut M4 Ground stud 4M x 12 Tab size 6. 3 x 0. 8
70(2. 736)
Cable length: 1. 5m. %%C4. 0 (0. 157)
4
132, 5 [5, 217]
5
2
ft M
ft M
144 [5, 669]
F
125 [4, 921]
Cut out
S
RD301
S
RD301
125 [4, 921]
(CD7018)
50(1. 968) 70(2. 736)
The drilling holes diam. [. . . ] No part of this document may be copied or reproduced in any form or by any means, and the information contained within is not to be communicated to a third party, without the prior written consent of Kongsberg Simrad AS.
Service
All service requests should be made to the local Kongsberg Simrad representative. Adjustments and repairs should only be performed by qualified service engineers, and unqualified repair attempts will void the warranty.
3
857-164821aa [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SIMRAD RD 301
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SIMRAD RD 301 will begin.