User manual SIMA SUR-47

[. . . ] SUR-47 Universal Touch Screen Remote Control with IR /RF transmission base unit User's Manual Preface SUR-47 User's Manual Preface About this manual This manual is designed to make using the SUR-47 Touch Screen Remote Control as easy as possible. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. Copyright © Copyright Sima Products Corporation 2003 This document contains proprietary information protected by copyright. No part of this manual may be reproduced by any mechanical, electronic or other means, in any form, without prior written permission of Sima Products Corporation. Trademarks All trademarks and registered trademarks are the property of their respective owners. FCC - The Federal Communication Commission Radio Frequency interference Statement includes the following paragraph: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. [. . . ] To operate in this mode, you must point the SUR-47 at the desired device. To operate in the RF mode, the SUR-47 transmits an RF frequency signal to the SUR-BU base unit, which sends an IR signal to the desired device. Both the device and the base unit must be set to the same RF address to operate properly. Press Press OK Select either IR to operate in the IR mode or an RF address (0-9) for the base unit and device If an RF address is selected, set the base unit to the same RF address by adjusting the ADDRESS wheel on the rear panel as needed. or to select ADDR 4. 10 SUR-47 User's Manual Specifications Deleting Devices Follow these instructions to delete a device configuration including the LCD display and codes. 1. Press Exit to exit the setup menu. Code Menu Enter the setup menus, scroll to Code and press to scroll through the code menu options: · to enter the code menu. In the code menu, press and Pre-Code - use this method to automatically configure all buttons on the SUR-47 for use with a specific manufacture model number. This feature is the fastest way to program the SUR-47 but requires that your device be located in the Pre-programmed Code List that was bundled with the SUR-47. Some newer or less-common devices may not be pre-programmed and must be learned using the Learning Function. Learn - use this method to directly learn the proper infrared signals from another remote control. This method is perfect for newer or less common devices or if a certain button still does not perform the desired function after using pre-programmed manufacturer codes; however, not 100% of codes can be learned and it may be necessary to collect unrecognized codes and send them to Sima Products. (See page 17 for more information on unrecognized code collection. ) Del Key - erases the key code Del Bank - erases the device code Debug - collects unrecognizable (un-learnable) infrared codes for debugging purposes · · · · 11 Getting Started SUR-47 User's Manual Using Pre-Code to Program Devices Follow these instructions to program a device using preprogrammed codes. Press or to select PRE-CODEand then press OK. Manually Selecting the Code 1. Check the preprogrammed code list that was bundled with the SUR-47 for the fourdigit code number of your device. Enter the four-digit code number and press YES button to confirm the entry. Note: If the code only has one digit (for example, 0001), you do not have to input the preceding zeros; in this example, press `1'. The device you are trying to control should turn on (or off) as you press this button. or to decrease or increase the four-digit code 5. You can also press number. Note: Some codes are designed to operate more than one model. It may take several tries to find the code that works with your unit. 12 SUR-47 User's Manual Specifications 6. Press YES to confirm the selection and save the settings or click EXIT to exit. Note: When you enter the Manufacture Code and an 'ERROR' message is displayed, it could be for two reasons: 1. That code number doesn't exist in the Manufacture Code table yet. That code number is not in the range of the Manufacture Code table reserved for the default device screen Selecting a Code Automatically 1. [. . . ] Check that the batteries are properly installed by pressing the SLEEP button. Make sure that the desired device screen on the SUR-47 LCD panel has been selected. Ensure programming with the learning function (page 12) or using the manufacturer codes (page 13) has been properly done. If you see the ERROR message when pressing buttons, re-teach the button. [. . . ]