User manual SIMA CP-150

[. . . ] User's Manual CP-150 Image Bank Sima Products Corporation Image Bank CP-150 Preface About this manual Introduction This manual is designed to make using the CP-150 Smart Remote Control as easy as possible. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. © Copyright 2001 This document contains proprietary information protected by copyright. No part of this manual may be reproduced by any mechanical, electronic or other means, in any form, without prior written permission of Sima Products Corp. Trademarks- all trademarks and registered trademarks are the property of their respective owners. FCC Rules & Warning This device complies with Part 15 of the FCC Rules. [. . . ] To identify the Image Bank as a removable drive, select the Removable Drive box and then assign a drive letter to it in the option box at the bottom of the screen. After assigning a drive letter, exit the Settings menus and reboot your computer. Caution: Before disconnecting the Image Bank or any USB device, break the USB connection by clicking on the icon on the lower right corner of the screen. Windows will display a message saying the USB Disk: (X) can now be safely removed from the system. During the installation process, if Windows cannot locate the diver by itself, you need to identify the location of the driver to the folder \Win98ME\ of the "USB Device Driver" disk. If you don't want to use Win98ME's default USB driver, you can change it. Please refer to "Win98ME_USB_Driver_Upgrade. pdf". For Windows 2000 users: No extra USB drivers needed in Windows 2000!During the installation process, if Windows cannot locate the diver by itself, you need to identify the location of the driver to the folder \Win2000\ of the "USB Device Driver" disk. If you don't want to use Win2000's default USB driver, you can change it. Please refer to "Win2000_USB_Driver_Upgrade. pdf". For Macintosh OS 9. 0/up users: 1. Insert the "USB Device Driver" disk to Mac, and download "usb2ide10F0" from the folder \Mac\ in the "USB Device Diver" disk to your Mac, then double click this file. Adapters are also available to use Sony MemoryStick and MMC cards. Trouble with unit and memory cards. 1. Make sure the unit is not connected to your PC or MAC and the USB cable is removed from the CP-150. (When USB cable is inserted in USB port on CP-150, it cannot read memory cards. ) 2. With unit off (LCD Display lights not lit) insert memory card and then power up the CP-150. If the memory cards are used (even just viewed) on a Mac with a reader, you will not be able to use the cards in the CP-150 unless they are re-formatted by the camera. When viewed with a MAC reader, Mac files are automatically be added to the CP-150. These will cause the copy process in the CP-150 to fail and the files will not be transferred. Trouble with unit and PC connection. 1. Plug in the power cord to the CP-150 No change on CP-150 panel Connect the USB cable to the CP-150 CP-150 Powers up, display flashes, HD on, ready light stays on. Does the computer recognize that something was just attached? 11 Image Bank Troubleshooting a CP-150 with a MAC Operating system: MAC OS9. 0 or higher 1). 2). Troubleshooting Make sure the unit and the USB cable is not connected to the MAC. after MAC recognizes the CD go to the MAC directory on the CDROM and copy the file USB2IDEDriver_20f4. HQX to the desktop 3). [. . . ] Touch only the sides of the hard drive, do not touch the printed circuit board. Attach the U-shaped bracket to the sides of the hard drive using the included screws but do not tighten. Place the hard drive on top of the circuit board of the CP-150 and carefully line up the IDE connector to the pins located on the back of the hard drive. Also make sure that the pins are lined up correctly with the connector on the CP-150 11. [. . . ]