User manual SILENT KNIGHT REGENCY 4720C-COMMERCIAL

[. . . ] Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Monitoring Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Intrusion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Pressing this button will also exit any of the special test modes and return the system to normal operation. Controls whether or not a chime tone will be generated when someone passes through a chime zone while the system is disarmed. It will not function unless the Model 4140 intercom system and the Model 4640 audio module are used. If you make a mistake while entering a code or command, press this button and start over. For zones that have been programmed with an entry or exit delay, pressing this button controls whether these zones will be delayed or instant. Delayed zones allow a user to exit after arming, or to disarm after entering, without generating an alarm. When the NO DELAY LED is on and the system is armed, zones programmed for entry and exit delay are instant. When pressed and held for one full second, this button generates an immediate alarm to the central monitoring station, indicating that the police should be dispatched. When pressed and held for one full second, this button generates an immediate alarm to the central station, from which the fire department will be dispatched. When pressed and held for one full second, this button generates an immediate alarm to the central monitoring station, for nonmedical emergency situations (typically silent alarm). (press twice) Page 8 User's Manual Section 3. Using Your Model 4720 Security System The following is an operating guide for each of your Model 4720 security system functions or capabilities. Go over each with your installer if you have any questions, and practice them until you feel comfortable with the day-to-day operation of each function. Arming Your System When leaving your office or business you will want to arm the intrusion protection of your security system as follows: 1. Enter your access code (3 to 6 digits) on the touchpad. Note: You have a 3-second timeframe to enter each digit of your access code. If you pause for 3 seconds, you will hear a short beep and the touchpad display will tell you to TRY AGAIN. If make a mistake entering your code, you can also press the CLR button and start over again. When you finish, the green READY light will go off, the red ARMED light will come on, and your system will be armed. (You and your alarm company will have determined the exact number of seconds necessary. ) The touchpad may give you an exit warning tone with beeps to count down your exit time for you. You must be out of the building with the door shut before the time runs out or an alarm will sound. If the touchpad shows a TROUBLE condition when you attempt to arm the system, contact your central station for servicing immediately. DO NOT attempt to arm the system until the TROUBLE condition is cleared as your system will not be fully operational. Disarming Your System To disarm, simply enter your access code (3 to 6 digits) on the touchpad. When you return and open a building door on the delay circuit, an entry warning tone will sound and you will have a programmed amount of time to enter and disarm the system. User's Manual Page 9 Model 4720 Commercial Security System The warning tone will stop as soon as you enter the first digit of your access code, allowing you to clearly hear the beeps as you finish entering your code. The LCD will show the number of seconds until the system does into alarm if not disarmed. [. . . ] System Messages Error Messages If operation or programming errors occur, the LCD will display the following messages to explain the problem: RESTRICTED CODE RESTRICTED DOOR RESTRICTED TIME RESTRICTED ZONE TRY AGAIN The touchpad or feature you are trying to use is not available with this code. Zone cannot be bypassed (fire or other 24-hour zones cannot be bypassed). Restart from the beginning. LCD Displays The English language LCD will normally display the day and time, plus status and instructions for many status lights and touchpad functions. The LCD will also display the following messages (in addition to trouble and error messages): # SEC TO ALARM This message provides a visual countdown of seconds before an alarm is sounded and sent to the control monitoring station. [. . . ]