User manual SILENT KNIGHT CENSUS 4821-COMMERCIAL 400 ZONES

[. . . ] Table of Contents System Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Multi-Area Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Special Information for Multi-Partition Maintenance Personnel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Code 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Normal User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Enter the number of the area where you want to turn off the interior zones. (Your system must be programmed for interior zones in this area). Repeat Steps 2 and 3 for each area where you want to turn off the interior zones. If the INTERIOR LED is also on, then the interior zones are also protected. When the INTERIOR LED is off, you can move freely within the interior zones, but the perimeter zones are armed. Flashing LEDs indicate that not all areas are armed. Arming/Disarming with Entry/Exit Delays Delay times give you time to leave your building after arming and return to your building to disarm your system without setting off alarms. The same instructions for "Arming/Disarming All Areas" applies; however, you must enter your access code within a specified number of seconds. (The number of seconds is programmed by your installer. ) The system beeps as the LCD displays the number of seconds before the system arms or an alarm sounds. 21 X X Activating Auto Arm Note: Auto Arm cannot be used in UL installations. If your system is programmed for the Auto Arm feature, the system can automatically arm itself. All you have to do is enter the number of minutes for the system to count down before arming. Note that when setting the arm time, the display will always show the default time of 10 minutes (not the previous arm time). Enter the number of minutes before auto arming goes into effect, then press ENTR (or just press ENTR 22 6. Press ENTR to return to the normal display. *Note: This feature is not available with toggle systems. What Happens The LCD will return to the normal display and the next automatic arming will occur at the new time. A message appears after the normal display messages warning you of how many minutes are left before automatic arming begins. to accept the default number of minutes). 5. Repeat Steps 2-4 to activate auto arming in other areas, or press ENTR to exit. X Cancelling Auto Arm If your system is programmed to arm automatically, you can manually turn off this feature. Resetting the time and date (page 29) automatically cancels auto arming. Enter the number of the area in which you want to cancel the auto arming. Press CLR 0 to erase the default number of minutes (10) before auto arming goes into effect, then press ENTR . Repeat Steps 2-4 to cancel auto arming in other areas, or press ENTR to exit. Press ENTR to return to the normal display. *Note: This feature is not available with toggle systems. What Happens The next automatic arming of the system will be cancelled. X Bypassing Zones Bypassing a zone means temporarily turning off protection to a part of your building. This enables you to access that zone and still protect the other areas in your building. You may also need to bypass a zone if you have a Not Ready condition that cannot be immediately corrected. (See page 36 for information about not ready conditions. ) You should not bypass fire or other 24-hour zones. [. . . ] Central Monitoring Station Your system reports alarms and other problems to the central station via the telephone lines. When emergencies occur, central station personnel dispatch the appropriate authorities. chime feature If the system is disarmed, a warning tone will sound whenever someone enters or leaves a zone programmed with the Chime feature. Code 2 feature Enables temporary users, such as guests and housekeepers, to operate the system during a timeframe designated by the main user. [. . . ]