User manual SIEMENS GIGASET S68H

[. . . ] s Issued by Gigaset Communications GmbH Schlavenhorst 66, D-46395 Bocholt Gigaset Communications GmbH is a trademark licensee of Siemens AG Gigaset Communications GmbH 2008 All rights reserved. www. gigaset. com Gigaset S68H Gigaset The handset at a glance The handset at a glance 17 16 V 1 2 INT 1 15. 11. 07 ?09:45 SMS 3 4 5 15 14 13 12 11 10 9 8 6 7 1 Display (screen) in idle status 2 Charge status of the batteries = e V U (flat to full) = flashes: batteries almost flat e V U flashes: batteries charging 3 Display keys (page 9) 4 Message key Access to calls and message lists; Flashes: new message or new call 5 End call key, On/Off key End call, cancel function, go back one menu level (press briefly), back to idle status (press and hold), activate/deactivate handset (press and hold in idle status) 6 Hash key Keypad lock on/off (press and hold in idle status); Toggle between upper/lower case and digits (press and hold) 7 Call-by-call list key Open call-by-call list 8 Microphone 9 Recall key - Confer (flash) - Insert a dialling pause (press and hold) 10 Star key Ringer tones on/off (press and hold); With an open connection: switch between dial pulsing/touch tone dialling (press briefly) Open special characters table 11 Key 1 Dial network mailbox (press and hold) 12 Connection socket for headset 13 Talk key Answer a call, open last number redial list (press briefly), start dialling (press and hold); When writing an SMS: send SMS 14 Handsfree key Switch between earpiece and handsfree mode; Lights up: handsfree activated; Flashes: incoming call 15 Control key (page 9) 16 Bluetooth activated (page 25) 17 Signal strength i (high to low) | flashes: no reception 1 Contents Contents The handset at a glance . 18 19 19 19 20 20 2 Safety precautions Safety precautions Warning: Read the safety precautions and the user guide before use. [. . . ] When the room monitor is activated, incoming calls to the handset are indicated without a ringer tone and are only shown on the screen. The display and keypad are not illuminated and advisory tones are also turned off. If you accept an incoming call, the room monitor mode is suspended for the duration of the call, but the function remains activated. If you deactivate then reactivate the handset, the room monitor mode remains activated. v Room Monitor Change multiple line input: Room M. : Select On to activate. Call to: External number: Select the number from the directory (press display key ) or enter it directly. Internal number: Options INT OK s (select handset or Call All if all registered handsets are to be called) OK. Press Save to save the settings. Activating the room monitor and entering the number to be called 17 Handset settings Changing the set destination number v Room Monitor s Scroll to the Call to: line. Enter and save number as described in "Activating the room monitor and entering the number to be called" (page 17). The number is then dialled or the function started by simply pressing a key. Assigning a digit key/left display key Precondition: The digit key or the left display key has not yet been assigned a number or a function. The following can be selected: Quick Dial / Call-by-Call Assign key to a number from the directory or call-by-call list. If you delete or edit an entry in the directory or call-by-call list, this has no effect on the assignment to the digit/ display key. Room Monitor Assign key to the menu for setting and activating the room monitor. Alarm Clock Assign key to the menu for setting and activating the alarm clock (see page 23). Depending on your base station, further key assignments are also possible. If the left display key has been assigned a shortcut, the selected function or name of the phone number in the directory or callby-call list is displayed (abbreviated if necessary) in the bottom display line via the display key. Deactivating the room monitor remotely Preconditions: The phone must support touch tone dialling and the room monitor should be set for an external destination number. no ringer tone) on the handset will remain activated until you press the display key OFF on the handset. To reactivate the room function with the same phone number: Turn on the activation again and save with Save. Handset settings Your handset is preconfigured, but you can change the settings to suit your individual requirements. Shortcuts for functions and numbers You can assign the left display key and each of the digit keys Q and 2 to O a number or a function. 18 Handset settings Starting the function, dialling the number If the handset is in idle status, press and hold the digit key or press the display key briefly. u The function menu is opened. Setting the display You have a choice of four colour schemes and several different contrasts. a Press and hold (idle status). Changing key assignments Display key key. Proceed as is described when first assigning the key with a shortcut (page 18). Press and hold the left or right display Setting the screensaver You can set a picture from the Resource Dir. (page 22) to be displayed as a screensaver when the handset is in idle status. If a screensaver is activated, the Screen Saver menu option is marked with . [. . . ] Contrast Select and press OK. Save Date: Enter the day, month and year in 8-digit format. Time: Enter hours/minutes in 4-digit format. Press on the bottom of control key q until the Contrast menu function is selected. Select contrast and press the display key Save. Press the s key. r Press on the right or left of the control key to set the contrast. Press the display key Save to confirm the selection. The fourth line is marked with [ ] to show it is active. [. . . ]