User manual SIEMENS GIGASET S67H

[. . . ] s Issued by Gigaset Communications GmbH Schlavenhorst 66, D-46395 Bocholt Gigaset Communications GmbH is a trademark licensee of Siemens AG Gigaset Communications GmbH 2008 All rights reserved. www. gigaset. com Gigaset S67H Gigaset The handset at a glance The handset at a glance 16 V 1 2 INT 1 15. 11. 07 ?09:45 SMS 3 4 5 15 14 13 12 11 10 9 8 6 7 1 Display (screen) in idle status 2 Charge status of the batteries = e V U (flat to full) = flashes: batteries almost flat e V U flashes: batteries charging 3 Display keys (page 9) 4 Message key Access to calls and message lists; Flashes: new message or new call 5 End call key, On/Off key End call, cancel function, go back one menu level (press briefly), back to idle status (press and hold), activate/deactivate handset (press and hold in idle status) 6 Hash key Keypad lock on/off (press and hold in idle status); Toggle between upper/lower case and digits (press and hold) 7 Call-by-call list key Open call-by-call list 8 Microphone 9 Recall key - Confer (flash) - Insert a dialling pause (press and hold) 10 Star key Ringer tones on/off (press and hold); With an open connection: switch between dial pulsing/touch tone dialling (press briefly) Open special characters table 11 Key 1 Dial network mailbox (press and hold) 12 Connection socket for headset 13 Talk key Answer a call, open last number redial list (press briefly), start dialling (press and hold); When writing an SMS: send SMS 14 Handsfree key Switch between earpiece and handsfree mode; Lights up: handsfree activated; Flashes: incoming call 15 Control key (page 9) 16 Signal strength i (high to low) | flashes: no reception 1 Contents Contents The handset at a glance . . 20 20 22 23 23 24 25 25 25 26 26 26 27 28 28 Operating the handset . [. . . ] The room monitor call to an internal number (handset) stops after approx. While the room monitor is activated, all keys are locked except the end call key. When the room monitor is activated, incoming calls to the handset are indicated without a ringer tone and are only shown on the screen. The display and keypad are not illuminated and advisory tones are also turned off. If you accept an incoming call, the room monitor mode is suspended for the duration of the call, but the function remains activated. If you deactivate then reactivate the handset, the room monitor mode remains activated. Managing entries in the last number redial list Press the key briefly. The following functions can be selected with q: Copy to Directory Copy an entry to the directory (page 12). Automatic Redial The selected number is automatically dialled at fixed intervals (at least every 20 seconds). The handsfree key flashes and "open listening" is activated. The function is ended after pressing any key or after ten unsuccessful attempts. Display Number (as in the directory, page 14) Delete Entry (as in the directory, page 14) Delete List (as in the directory, page 14) c s 16 Using a handset as a room monitor Caution! You should always check the operation of the room monitor before use. Check the connection if you are diverting the room monitor to an outside number. When the function is switched on the handset's operating time is severely reduced. Ideally the handset should be positioned 1 to 2 metres away from the baby. The connection to which the room monitor is diverted must not be blocked by an activated answer machine. v Room Monitor s Scroll to the Call to: line. Enter and save number as described in "Activating the room monitor and entering the number to be called" (page 17). Changing the set destination number Deactivating the room monitor remotely Preconditions: The phone must support touch tone dialling and the room monitor should be set for an external destination number. no ringer tone) on the handset will remain activated until you press the display key OFF on the handset. To reactivate the room function with the same phone number: Turn on the activation again and save with Save. v Room Monitor Change multiple line input: Room M. : Select On to activate. Call to: External number: Select the number from the directory (press display key ) or enter it directly. Internal number: Options INT OK s (select handset or Call All if all registered handsets are to be called) OK. Press Save to save the settings. Activating the room monitor and entering the number to be called 17 Handset settings Handset settings Your handset is preconfigured, but you can change the settings to suit your individual requirements. Open calendar/enter new appointment. Depending on your base station, further key assignments are also possible. [. . . ] This is illustrated below using the example of "Setting the date and time". You will see the following display (example): Date/Time Date: [15. 11. 2007] Time: 11:11 With the handset in idle status, press v Display on the right of the control key (v) to open the main menu. Press on the bottom of control key q until the Display menu function is selected. Contrast Select and press OK. Save Date: Enter the day, month and year in 8-digit format. [. . . ]