User manual SIEMENS GIGASET S18H

[. . . ] s Issued by Gigaset Communications GmbH Schlavenhorst 66, D-46395 Bocholt Gigaset Communications GmbH is a trademark licensee of Siemens AG Gigaset Communications GmbH 2009 All rights reserved. www. gigaset. com Gigaset S18H Gigaset The handset at a glance The handset at a glance 1 Display in idle status 2 Charge status of the batteries = e V U (empty to full) = flashes: batteries almost empty e V U flashes: batteries charging 3 Display keys (page 15) 4 Message key Access to calls and message lists; Flashes: new message 5 Flash key - Confer (Flash) - Insert a dialing pause (press and hold) 6 End call key, On/Off key End call, cancel function, go back one menu level (press briefly), back to idle status (press and hold), activate/deactivate handset (press and hold in idle status) 7 2. 5 mm socket for headset (mono) 8 Pound (#) key Key lock on/off (press and hold in idle status) Toggle between upper/lower case and digits 9 Microphone 10 Star (*) key Ringtones on/off (press and hold) Open table of special characters 11 Key 1 Fast access to answering machine/network mailbox (press and hold) 12 Talk key Answer a call, start dialing 13 Handsfree key Switch between earpiece and handsfree mode; Lights up: handsfree activated; Key flashes: incoming call 14 Control key (page 14) 15 Signal strength i (high to low) | flashes: Out of Range 15 INT 1 V 1 2 01. 31. 09 9:45am Menu 3 14 13 12 11 7 10 8 4 5 6 9 1 Contents Contents The handset at a glance . 24 24 25 25 25 26 26 27 27 27 Gigaset S18H more than just a telephone . 38 2 Safety precautions Safety precautions* $ Power Outage: ! Only use the power supply unit supplied as indicated on the underside of the device. In the event of a power outage, your cordless telephone will not operate. [. . . ] You can store an internal or external number in your handset as the destination number. The room monitor call to an internal number (handset) stops after approx. While the room monitor is activated, all keys are locked except the end call key. When the room monitor is activated, incoming calls to the handset are indicated without a ringtone and are only shown on the screen. The display and keypad are not illuminated and advisory tones are also turned off. If you accept an incoming call, the room monitor mode is suspended for the duration of the call, but the function remains activated. You will need to reactivate the function after switching on the handset again. Caution: You should always check the operation of the room monitor before use. Check the connection if you are diverting the room monitor to an outside number. When the function is switched on the handset's operating time is severely reduced. Ideally the handset should be positioned 1 to 2 meters away from the sound being monitored. The connection to which the room monitor is diverted must not be blocked by an activated answering machine. v Room Monitor Change multiple line input: Room M. : Select On to activate. INT s (select handset or Call All, if all registered handsets are to be called) OK. With Options, you can move directly to settings. Activating the room monitor and entering the number to be called 23 Handset settings v Room Monitor s Scroll to the Call to: line. Enter number as described in "Activating the room monitor and entering the number to be called" (page 23). Save changes (page 6). Changing previously set external destination number Handset settings Your handset is preconfigured, but you can change these settings to suit your individual requirements. Changing the display language You can view the display texts in different languages. If you accidentally choose a language you do not understand: v 5 41 Press display keys one after the other. s Select the correct language and press OK. Changing previously set internal destination number v Room Monitor s Scroll to the Call to: line. Enter number as described in "Activating the room monitor and entering the number to be called" (page 23). Save changes (page 6). Deactivating the room monitor remotely Important: The destination phone must support touch tone dialing and the room monitor must be set for an external destination number. The external caller will hear a deactivation signal tone and then the call will end. But the other room monitor settings on the handset (such as no ringtone) will remain activated until you press the display key OFF on the handset. To reactivate the room function with the same phone number: Turn on the activation again and save (page 23) with Save. Setting the display You have a choice of four color schemes and several different contrasts. [. . . ] Some states/jurisdictions/provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. You may have others which vary from state/jurisdiction/province to state/jurisdiction/province. 7. WARRANTY CLAIM PROCEDURE All warranty claims must be made by notifying Gigaset NAM prior to the expiration of the warranty period. Gigaset NAM's obligation to provide warranty support shall not extend past the end of the warranty period, except that any product repaired or replaced during the warranty period shall continue to be warranted for the balance of such warranty period or thirty (30) days, whichever is greater. [. . . ]