User manual SIEMENS GIGASET S185

[. . . ] s Version: 23-06-2009 A 3 1 0 0 8 - M1 7 2 9 - R4 0 1 - 1 - 5 8 1 9 Issued by Gigaset Communications GmbH Schlavenhorst 66, D-46395 Bocholt Gigaset Communications GmbH is a trademark licensee of Siemens AG Gigaset Communications GmbH 2009 All rights reserved. www. gigaset. com Gigaset S185 Gigaset The handset at a glance The handset at a glance 16 15 INT 1 V 1 2 01. 31. 08 9:45am Menu 3 14 13 12 11 7 10 8 4 5 6 9 1 Display in idle status 2 Charge status of the batteries = e V U (empty to full) = flashes: batteries almost empty e V U flashes: batteries charging 3 Display keys (page 16) 4 Message key Access to calls and message lists; Flashes: new message 5 Flash key - Confer (Flash) - Insert a dialing pause (press and hold) 6 End call key, On/Off key End call, cancel function, go back one menu level (press briefly), back to idle status (press and hold), activate/deactivate handset (press and hold in idle status) 7 2. 5 mm socket for headset (mono) 8 Pound (#) key Key lock on/off (press and hold in idle status) Toggle between upper/lower case and digits 9 Microphone 10 Star (*) key Ringtones on/off (press and hold) Open table of special characters 11 Key 1 Fast access to answering machine/network mailbox (press and hold) 12 Talk key Answer a call, start dialing 13 Handsfree key Switch between earpiece and handsfree mode; Lights up: handsfree activated; Key flashes: incoming call 14 Control key (page 15) 15 Answering machine symbol Answering machine switched on. Flashes: answering machine is recording a message or is being operated by another caller. 16 Signal strength i (high to low) | flashes: Out of Range 1 Base station at a glance Base station at a glance 3 4 5 2 1 6 7 Please remember: u If the answering machine is being oper- ated from a handset or if it is recording a message, it cannot be operated from the base station. [. . . ] Before each voice command, press 9 and then speak the command when you hear the 'ready' tone. Repeat "DELETE", without first pressing the 9. Activating the answering machine Phone home and allow the phone to ring until you hear: "Please enter PIN". The answering machine cannot be deactivated remotely. 28 Using the network mailbox Using the network mailbox The network mailbox is your network provider's answering machine within the network. You cannot use the network mailbox unless you have requested it from your network provider. Calling the network mailbox 1 d Press and hold. You hear the network mailbox announcement. Configuring the network mailbox for fast access With fast access, you can dial either the network mailbox or your integrated answering machine directly. Ask your network provider about this. Viewing the network mailbox message If a message arrives for you, you receive a call from the network mailbox. If you have requested Caller ID, the display shows the network mailbox number. If you do not accept the call, the network mailbox number will be stored in the missed calls list and the message key will flash (page 20). v Voice Mail Set Key 1 Network Mailb. If your network mailbox requires a password for access, it is possible to add a password by entering pauses (see Flash key on page 1) immediately after entering the mailbox access number, then enter your password. The Gigaset S185 will dial the mailbox number, wait a few seconds until the mailbox is accessed, then dial your password. If more time is needed for your mailbox to answers before the network mailbox password is dialed, simply add an additional pause (P). 29 Configuring the network mailbox for fast access and entering the network mailbox number Using several handsets Using several handsets Registering handsets You can register up to a total of six handsets on your base station. A Gigaset handset can be registered on up to four base stations. Manual registration: Gigaset handset to Gigaset S185 base station You must activate manual registration of the handset at both the handset and the base station. The internal number of the handset appears in the display, for example INT 1. v Handset Register H/Set s Select base station, for example Base 1 and press OK. ~ Enter the system PIN of the base station (the default is 0000) and press OK. The screen will display the number, for example Base 1. Automatic registration: Gigaset handset to Gigaset S185 base station Important: The handset must not yet be registered to any base station. Registering the handset to the Gigaset S185 base station occurs automatically. During this process, Regstr. Procedure appears in the display and the name of the base station flashes, for example Base 1. When the handset has been registered, its screen displays its internal number, for example INT 2 for internal number 2. If all internal numbers 1-6 have been assigned, number 6 is overwritten, assuming that the handset with the internal number 6 is in idle status. On the handset On the base station Within 60 secs. press and hold the registration/paging key on the base station (page 2) (approx. [. . . ] WARRANTY CLAIM PROCEDURE All warranty claims must be made by notifying Gigaset NAM prior to the expiration of the warranty period. Gigaset NAM's obligation to provide warranty support shall not extend past the end of the warranty period, except that any product repaired or replaced during the warranty period shall continue to be warranted for the balance of such warranty period or thirty (30) days, whichever is greater. Support service will be provided for you by accessing the toll free customer service number: 1-866-247-8758 5. LIMITATION OF WARRANTY Gigaset NAM makes no warranty or representation that the software in the Products will meet your requirements or will work in combination with any hardware or applications software GIGASET NAM AND ITS SUPPLIERS PROVIDE THE PRODUCT AND SUPPORT SERVICES (IF ANY) AS IS AND WITH ALL FAULTS. [. . . ]