User manual SIEMENS GIGASET C610A IP

[. . . ] Navi key When the telephone is idle In lists and menus Upward Open directory Open menu Downward Select entry (OK) In an entry field Cursor one line up Cursor one line down Cursor to the right Cursor to the left E D G F Open the list of inter- One menu level nal users back (cancel) Displays The following symbols appear in the display, depending on the operating situation: Soft keys MENU Meaning Menu button: Activate the general menu when telephone is idle. Displays if telco voice mail or call log is active One menu level back, cancel Z W { I Í Example for Menu Operation: Setting the Volume for the Speakerphone 1. Store the required volume for speakerphone. Z Z G or F Save V Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1- umschl_v. fm 25. 09. 0 General VI Gigaset 4010 Comfort, CHIN eng, A31008-G4010- 4010CoIVZ. fm 25. 09. 0 Contents Setting Up the Telephone . 56 1 Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 vorberei. fm 25. 09. 03 Setting Up the Telephone Setting Up the Telephone This delivery units contains: · · · · · · · · 1 Gigaset base station 1 Gigaset S 88 handset 1 power supply unit 1 telephone cord 1 belt clip 2 AA rechargeable NiCd batteries 1 user manual 1 Quick Start Guide Installing the Base Station F The base station is designed for operation in protected rooms with a temperature range from +40°F to +100°F. [. . . ] A handset can only be registered to one Gigaset base station at a time. Step 1: On the Handset MENU Press Menu. D åååååååååååååååååååååååååååååååå [ Scroll to H/Set Settings and press OK. H/Set Settings D åååååååååååååååååååååååååååååååå [ Scroll to Reg. Handset D [ Select the base station ( Base 1 is recommended unless you are registering your handset to an additional base). Step 2: Underside of the base station o [ Enter the PIN (factory setting: 0000). Hold down the Page/Registration key on the underside of the base station for approximately 5 seconds until a signal tone is heard at the base station. When the handset has been successfully registered, the intercom number is shown (for example, "INT1"). If all internal handset numbers are assigned, the intercom number 4 is reassigned. The handset that has been registered under number 4 will be deregistered. 30 Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 mobilt_an. fm 25. 09. 03 Handset Operation Press keys: Deregistering Handsets Prerequisite: You can only deregister Gigaset S88 handsets. F Press left on the navi key (INT) and the list of handsets is displayed. E D Scroll to the handset that is to be deregistered. MENU Press Menu. D åååååååååååååååååååååååååååååååå [ Scroll to Dereg. Handset PIN [ Enter the PIN (factory setting 0000) and press OK. Yes a Confirm by pressing Yes. You can only deregister handsets with a Gigaset S88. Switching Base Stations Prerequisite: The handset is registered at more than one base stations. at home or in the office) set to Best Base and it is automatically switched to the base station with the best reception. or MENU G Press Menu. D åååååååååååååååååååååååååååååååå [ Scroll to H/Set Settings and press OK. The number you store can be: G G An internal number - An additional registered handset required. An external number - A cell phone number or another fixed network number where you can be contacted (i. e. If you use an external telephone number for the room monitor you should inform the owner of the telephone so that the call from the room monitor is answered. Incoming Calls on the Handset Set to Room Monitor Incoming calls on the handset being used as the room monitor: G G G Signaled without the ringer The call is only displayed. This feature considerably reduces the operating time of the handset being used as the room monitor. 36 Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 mobilt_an. fm 25. 09. 03 Handset Operation Press keys: Storing the Internal Number for the Room Monitor MENU Press Menu. D åååååååååååååååååååååååååååååååå [ Scroll to Room Mon. D åååååååååååååååååååååååååååååååå [ Scroll to Room Monitor and press OK. F G Press left or right on the navi key to turn On and Off the room monitor feature. D Edit Scroll down one line to Set No. line has an existing external number you can overwrite it with X first. Press Edit and enter the required telephone number. D E [ Scroll to desired internal number and press OK. F G Press left or right on the navi key to set the sensitivity level to "high" or "low" Save Press Save. F Press INT. D Scroll down one line to Set Level. The room monitor is now on. It can be turned off by pressing the soft key marked Off on the handset set to monitor. 37 Gigaset 4010 Comfort, CHIN eng, A31008-G4010-C102-1-7619 mobilt_an. fm 25. 09. 03 Handset Operation Press keys: Storing an External Number for Room Monitoring MENU Press Menu. D åååååååååååååååååååååååååååååååå [ Scroll to Room Mon. D åååååååååååååååååååååååååååååååå [ Scroll to Room Monitor and press OK. [. . . ] If the product is repaired, reconditioned component parts or materials may be used. If the product is replaced, we may choose to replace it with a new or reconditioned product of the same or similar design. The repaired or replacement product will be warranted for either (a) 90 days or (b) the remainder of the original one (1) year warranty period, whichever is longer. Batteries are warranted to be free from defects at the time of purchase. [. . . ]