User manual SIEMENS GIGASET C360

[. . . ] The appropriate disposal and separate collection of used equipment serve to prevent potential harm to the environment and to health. They are a precondition for the re-use and recycling of used electrical and electronic equipment. For further information on disposing of your used equipment, please contact your local authority, your refuse collection service or the dealer you purchased the product from. Emergency numbers cannot be dialled if the key lock (page 1) is activated! [. . . ] Once the phone is registered and the time set, the idle display looks as shown on page 1. Displaying the caller's phone number When you get a call, the caller's phone number will be displayed on your handset; or the caller's name will be displayed if it is stored in the directory or if CNIP has been requested. Requirements: 1 You have asked your network provider for the caller's phone number (CLIP) or name (CNIP) to be displayed on your handset screen. 2 The caller has asked the network provider for his phone number to be identified (CLI). ® appears in the display if you have not requested Calling Line Identification, Withheld appears if the caller has withheld CLI, and Unavailable if CLI has not been requested by the caller. Handsfree talking Once you have entered the phone number you can immediately call in handsfree mode by pressing d (the d key lights up continuously). During a call you can switch between earpiece and handsfree mode by pressing d. Set the handsfree volume with u. 4 Operating the handset Activating/deactivating the handset Press and hold the end call key a. If you place a deactivated handset in the base station or charging cradle, it will automatically activate. The following functions can be selected with u: New Entry Show Number Use Number Add a new entry. For speed dial, assign the current entry to a key. Edit Entry Delete Entry Send Entry Delete List Send List Shortcut Using the directory and lists Directory To open the directory: press v . Note: You can assign a number from the directory to a key for speed dial (page 4). Setting the shortcut key Saving the first number in the directory v ¢ New Entry?Enter name and press OK. MENU Scroll touShortcut Scroll u to select a number (0, 2-9), for example: Shortcut: 2 OK ¢ ¢ ¢ Using the shortcut key By pressing and holding the shortcut key, the relevant IP or VIP number will be dialled. (For example: press and hold key 2, the IP number will be dialled, then dial the long distance number) Saving a number in the directory v ¢ MENU ¢ New Entry ¢ OK ~ ~ Enter number and press OK. Enter name and press OK. Sending the directory to another handset Preconditions: The sending and receiving handsets must both be registered to the same base station. The other handset and the base station can send and receive directory entries. lowing options: Use u to scroll to the entry until the required name is selected. Enter the first character of the name or scroll to the entry with u, if required. Selecting a directory entry Open the directory with h or v. You have the fol- v ¢ u (Select entry) ¢ MENU ¢ Send Entry / Send List ¢ OK ¢ ~ (Enter the internal number of the receiving handset) ¢ OK Dialling with the directory v ¢ u (Select entry) ¢ c Using other functions v ¢ v (Select entry) ¢ MENU 5 Last number redial list This list contains the ten last dialled numbers. Calls list Precondition: CLIP (page 3) The numbers of the last 20 incoming calls are saved. The calls list is displayed as follows: CallsList 01+02 Number of new entries + number of old, read entries Dialling from the last number redial list c c Press the key briefly. The number is dialled. u Managing entries in the last number redial list c Press the key briefly. Press the display key. Opening the calls list f ¢ CallsList 01+02 ¢ OK Select entry with u. Using other functions u MENU u (Select entry) ¢ MENU Delete Entry Copy to Dir. Date/Time Status You can select the following functions: Use Number Copy to Dir. Delete Entry Delete List The following functions can be selected with u: Delete current entry. If you have requested CNIP, you can show the name and town that are registered for your phone number with your network provider. [. . . ] No wireless The handset is Move the handset connection to outside the range closer to the base the base sta- of the base stastation. Cords not routed Check cord routing correctly (page 2). Care Wipe the base stationand handset with a damp cloth (do not use solvents) or an antistatic cloth. This can cause static. Service (Customer Care) We offer you support that is fast and tailored to your specific needs!Our Online Support on the Internet: www. gigaset. com/customercare For more information on aftersales service, please refer to your local warranty card. [. . . ]