User manual SIEMENS GIGASET AS140

[. . . ] EN Dear Customer, Gigaset Communications GmbH is the legal successor to Siemens Home and Office Communication Devices GmbH & Co. Any statements made by Siemens AG or SHC that are found in the user guides should therefore be understood as statements of Gigaset Communications GmbH. Sehr geehrte Kundin, sehr geehrter Kunde, die Gigaset Communications GmbH ist Rechtsnachfolgerin der Siemens Home and Office Communication Devices GmbH & Co. KG (SHC), die ihrerseits das Gigaset-Geschäft der Siemens AG fortführte. [. . . ] auto paint shops). $ If you give your Gigaset to someone else, make sure you also give them the operating manual. Fit only the approved rechargeable battery pack!Never use a conventional (non-rechargeable) battery pack as this could damage your health and cause injury. Be aware of the technical conditions within the particular environment (e. g. Do not hold the handset against your ear while it is ringing (incoming call). Dispose of the battery pack and telephone in accordance with environmental regulations. Do not pollute the environment. Emergency numbers cannot be dialled if the keypad lock (page 3) is activated!Not all of the functions described in this manual are available in all countries. 2 Setting up the telephone for use Step 1: Connecting the base Opening the battery cover Press down on the battery cover below its upper end and slide the cover down. 1 2 W Connect the phone jack with the phone cord 1 and the mains units (230 V) with the power cord 2 as shown. If you ever purchase another phone cord from a store, ensure that the phone conductors are correctly connected: 3-4 connection of the telephone conductors/EURO CTR37. Place the battery leads in the cable guides so that the battery cover cannot catch on the leads and damage them when it is closed. never use a normal battery pack as this could damage your health and cause injury. Never use non-Siemens battery chargers as this could damage the battery pack. (Or you can first press c [dial tone] and then enter the number. ) During the call you can adjust the earpiece volume with t and s. You can automatically insert a network provider prefix before any number (see Menu Tree, PRESELECT, page 9). Using the directory and other lists Directory and speed dial list These two lists are used in the same way. private phone numbers, prefixes of network providers ("Call-by-Call") etc. The following functions are available: EDIT ENTRY NEW ENTRY SHOW ENTRY DELETE ¢c. Answering a call Your handset rings and you wish to take the call: Press the talk key c. If "Auto Answer" is active (page 6) just lift the handset out of its base/charging cradle. Add/edit number and use to dial Save new phone number Show/edit number Delete a single entry Clear the list: h/C¢MENU¢L ¢OK. Calling Line Identification When you get a call, the caller's number will be displayed on your handset; the caller's name will be displayed if it is stored in the directory . Requirements: 1 You have asked your network provider for the caller's number (CLIP) to be displayed on your handset screen. 2 The caller has asked the network provider for his number to be identified (CLI). The display shows if you have not requested CLIP, WITHHELD if the caller has withheld CLI, or UNAVAILABLE if it has not been requested. Storing a number in the directory/speed dial list h/C¢ MENU ¢ NEW ENTRY ~OK ~OK Enter phone number and confirm. Speed dial: Enter the digit of the required speed dial key (2­9), then enter the name and confirm. Long press (back to idle status). a Table for text/numerical entry: see page 6. Cursor control: see page 1. 4 Dialling with the directory h ~ s c Open the directory. Press the talk key. Û Select an entry (see above)¢ MENU. The following functions are available: DELETE COPY TO DIR TIME STATUS DELETE LIST Using the calls list ¢ Delete an individual number Store a number in the directory. [. . . ] This can cause static! Authorisation This device is intended for connection to analogue networks outside the EEA (with the exception of Switzerland) depending on national type approval. KG, declare that this device meets the essential requirements and other relevant regulations laid down in Directive 1999/5/EC. A copy of the 1999/5/EC Declaration of Conformity is available at this Internet address: http://www. siemens. com/gigasetdocs. Contact with liquid ! If the handset has come into contact with liquid: 1 Switch the handset off and remove the battery pack immediately. 3 Pat all parts dry, then place the handset with the battery compartment open and the keypad facing down in a dry, warm place for at least 72 hours (not in a microwave, oven etc. ). [. . . ]