User manual SIEMENS GIGASET A270

[. . . ] EN Dear Customer, Gigaset Communications GmbH is the legal successor to Siemens Home and Office Communication Devices GmbH & Co. Any statements made by Siemens AG or SHC that are found in the user guides should therefore be understood as statements of Gigaset Communications GmbH. Sehr geehrte Kundin, sehr geehrter Kunde, die Gigaset Communications GmbH ist Rechtsnachfolgerin der Siemens Home and Office Communication Devices GmbH & Co. KG (SHC), die ihrerseits das Gigaset-Geschäft der Siemens AG fortführte. [. . . ] Confirm menu function or store an entry. 4 5 6 Þ Ü INT MENU 7 8 9 10 11 t u and s ß OK and v Safety precautions W Read this manual and the safety precautions carefully before use. Explain their contents to your children, and the potential hazards associated with using the telephone. Only use the mains unit supplied. Do not install the phone in a bathroom or shower room as the handset and base are not splash-proof. (page 7) Do not use the telephone in environments subject to explosion hazard (e. g. auto paint shops). $ If you give your Gigaset to someone else, make sure you also give them the operating manual. Fit only the approved rechargeable battery pack!Never use a conventional (non-rechargeable) battery pack as this could damage your health and cause injury. Be aware of the technical conditions within the particular environment (e. g. Do not hold the handset against your ear while it is ringing (incoming call). Dispose of the battery pack and telephone in accordance with environmental regulations. Do not pollute the environment. Emergency numbers cannot be dialled if the keypad lock (page 2) is activated!Not all of the functions described in this manual are available in all countries. 2 Setting up the telephone for use Step 1: Connecting the base Step 3: Registering the handset to the base and charging the battery pack Place your handset in the base with the display facing forwards. For procedure see page 4. Charging the battery pack 1 2 Connect the phone jack with the phone cord 1 and the mains units (230 V) with the power cord 2 as shown. If you ever purchase another phone cord from a store, ensure that the phone conductors are correctly connected: 3-4 connection of the telephone conductors/EURO CTR37. To charge the battery pack, leave the handset in the base for approx. The charge status of the battery pack is correctly displayed only after uninterrupted charging/discharging. The following functions are available: EDIT ENTRY NEW ENTRY DISPLAY ENT DELETE Edit number and use to dial Save new phone number Show/edit number Delete a single entry h/C¢MENU¢L ¢OK. Storing a number in the directory/speed dial list Clear the list separately: Answering a call Your handset rings and you wish to take the call: Press the talk key c. If "Auto Answer" is active (page 5) just lift the handset out of its base/charging cradle. h/C¢ MENU ¢ NEW ENTRY ~OK ~OK Enter phone number and confirm. Speed dial: Enter the digit of the required speed dial key (2­9), then enter the name and confirm. Long press (back to idle status). Calling Line Identification When you get a call, the caller's number will be displayed on your handset; the caller's name will be displayed if it is stored in the directory . Requirements: You have asked your network provider for the caller's number (CLIP) to be displayed on your handset screen. The display shows if you have not requested CLIP. a Table for text/numerical entry: see page 6. Cursor control: see page 1. Dialling with the directory h ~ s c Open the directory. Press the talk key. Muting You can mute your handset when making external calls. To cancel the function: Press a briefly. Speed dialling Example: the stored name is , , 3Anna". [. . . ] To activate: MENU O 4 1. Appendix Character set chart Press the required key the number of times indicated. 1x Q 1 R P + Space ¢ ¢ 2x 0 1 / 3x - 4x | 5x ? 6x _ Resetting the handset Restoring the factory settings of the handset will not affect entries in the directory, the calls list or the speed dial list or the handset's registration to the base. MENU # (appears in display as j) * ( ) , ¢ OI ¢ RESET ?¢ OK. Specifications Power consumption of base In ready status: approx. 2 Watt. Base station settings Changing pause after line seizure You can change the length of the pause that is inserted between pressing the talk key c and sending the number: MENU NO1L The digit for the current pause length flashes: 1 = 1 sec. ; 2 = 3 sec. ; 3 = 7 sec. ; 4 = 2. 5 sec. [. . . ]