User manual SIEMENS GIGASET 5020 QUICK GUIDE

[. . . ] 1 GB Gigaset 5020* Quick Guide 9 10 11 12 1 8 7 6 Pause No memory content { Telephone locked When trying to connect: telephone locked zzzz 0­9 Phone number With tone dialling: n ­ * key pressed ­ # key pressed With additional services from public network providers: New call in calls list (Flashing) A new message has arrived ë Call waiting TM Call forwarding immediately ~ Call forwarding on no reply -- Call forwarding when busy s Anonymous call on P z | 5 4 3 2 Safety precautions When installing, connecting and operating the telephone, always observe the following precautions: Only use the plugs and leads supplied. Only connect the connecting lead to the socket/jack provided for that purpose. For your safety and protection, the telephone must not be used in bath or shower rooms (wet locations). Never expose the telephone to sources of heat, direct sunlight or other electrical devices. [. . . ] If no external line prefixe has been set in a location, z appears in the display. If several external line prefixes are saved, these are displayed next to one another; the current external line prefixe to be edited flashes. If necessary, use the ; key to toggle between the external line prefixes displayed, to edit them as follows: To delete an external line prefix: ?To enter an external line prefixe: o Enter a one- to three-digit code. Enter additional external line prefixes: ;o Press the Redial key, enter next external line prefixe. Press the Set key. Setting the pause time If necessary, the pause time of the Pause key ; (pause function from second input position) can be changed to 1, 3 or 6 seconds (default setting: 3 seconds). ?102 0. . . 2 0: 1 sec. ; 1: 3 sec. ; 2: 6 sec. . Press the Set key. Initiate function. Changing the dialling mode ?# Initiate function. 1/ 2 1: Tone dialling. ? 2: Pulse dialling without flash function. Press the Set key. Changing dialling modes during a call If your telephone is set to pulse dialling and you want to use functions that require tone dialling (e. g. remote access to an answering machine), you can change the dialling mode during a call. The telephone is reset to the original dialling mode by hanging up the handset. Recall key (on a PABX) During an external call, you can make a recall or divert the call. By default, the Recall key is preset to a flash time (interruption time) of 90 ms for use of new features on public telephone systems. With a connection to a PABX, it may be necessary to change the flash time (e. g. Its position number "01" is displayed to the left of the number. If the phone number contains more than 17 digits, the first 17 digits will be displayed first, then the rest after one second. (You can leave the calls list at any time by pressing >. ) To scroll through the calls list: A. . . C Press the Down/Up key. The date and time of the displayed entry is displayed with the number of calls (on the right). Back to the calls list (calling line display): = Press the Shift key again. Lift the handset if you want to talk via the handset. | Using Calling Line Identification Under the following conditions, the phone numbers of incoming calls are (a) shown on the display (up to the first 20 digits) and (b) automatically saved in a calls list: Both your network provider and the caller's network provider must offer Calling Line Identification. Both you and the caller must have requested this service (if necessary) from your respective network providers. If these conditions are met, but a caller has suppressed Calling Line Identification before making the call, you will see ---P--- on the display instead of the phone number. If it has not been possible to identify the number for other (technical) reasons, you will see ---0--- or ---E--- on the display. [. . . ] When "Call forwarding immediately" is activated later, this key makes the cursor for entering the phone number of the forwarded call destination flash. (a) Phone number for call forwarding set You may hear an announcement that the service is activated. From now on, incoming calls will be forwarded to the forwarded call destination. Your telephone will not ring. o # ? or . . . Example: Call forwarding In the following, you will see an example of repertory keys used as "function keys". [. . . ]