User manual SIEMENS GIGASET A120 DUO

[. . . ] EN Dear Customer, Gigaset Communications GmbH is the legal successor to Siemens Home and Office Communication Devices GmbH & Co. Any statements made by Siemens AG or SHC that are found in the user guides should therefore be understood as statements of Gigaset Communications GmbH. Sehr geehrte Kundin, sehr geehrter Kunde, die Gigaset Communications GmbH ist Rechtsnachfolgerin der Siemens Home and Office Communication Devices GmbH & Co. KG (SHC), die ihrerseits das Gigaset-Geschäft der Siemens AG fortführte. [. . . ] auto paint shops). $ If you give your Gigaset to someone else, make sure you also give them the operating manual. Fit only the approved rechargeable battery pack!Never use a conventional (non-rechargeable) battery pack as this could damage your health and cause injury. Be aware of the technical conditions within the particular environment (e. g. Do not hold the handset against your ear while it is ringing (incoming call). Dispose of the battery pack and telephone in accordance with environmental regulations. Do not pollute the environment. Emergency numbers cannot be dialled if the keypad lock (page 3) is activated!Not all of the functions described in this manual are available in all countries. 2 Setting up the telephone for use Step 1: Connecting the base Step 3: Registering the handset to the base and charging the battery pack Place your handset in the base with the display facing forwards. For procedure see page 4. Charging the battery pack 1 2 Connect the phone jack with the phone cord 1 and the mains units (230 V) with the power cord 2 as shown. If you ever purchase another phone cord from a store, ensure that the phone conductors are correctly connected: 3-4 connection of the telephone conductors/EURO CTR37. The range may be affected if the telephone is wall mounted. To charge the battery pack, leave the handset in the base for approx. The charge status of the battery pack is correctly displayed only after uninterrupted charging/discharging. End the call/cancel dialling: Press the end call key a. Using the directory and other lists Directory and speed dial list These two lists are used in the same way. private phone numbers, prefixes of network providers ("Call-by-Call") etc. The following functions are available: EDIT ENTRY NEW ENTRY SHOW ENTRY DELETE ¢c. Answering a call Your handset rings and you wish to take the call: Press the talk key c. If "Auto Answer" is active (page 6) just lift the handset out of its base/charging cradle. Add/edit number and use to dial Save new phone number Show/edit number Delete a single entry Calling Line Identification When you get a call, the caller's number will be displayed on your handset; the caller's name will be displayed if it is stored in the directory . Requirements: 1 You have asked your network provider for the caller's number (CLIP) to be displayed on your handset screen. 2 The caller has asked the network provider for his number to be identified (CLI). The display shows if you have not requested CLIP, WITHHELD if the caller has withheld CLI, or UNAVAILABLE if it has not been requested. Clear the list: h/C¢MENU¢L ¢OK. Storing a number in the directory/speed dial list h/C¢ MENU ¢ NEW ENTRY ~OK ~OK Enter phone number and confirm. Speed dial: Enter the digit of the required speed dial key (2­9), then enter the name and confirm. Long press (back to idle status). a Table for text/numerical entry: see page 6. Cursor control: see page 1. 4 Dialling with the directory h ~ s c Open the directory. Press the talk key. Û Select an entry (see above)¢ MENU. The following functions are available: DELETE COPY TO DIR TIME STATUS DELETE LIST Using the calls list ¢ Delete an individual number Store a number in the directory. [. . . ] 116 g NiMH, 2xAAA Pack V30145-K1310-X359, A5B00075178739 550 mAh approx. 140 hours (6 days) Problem No response to key press, "HOLD KEY" appears in the display. No wireless connection to the base, different icons flash in the display. Cause Solution The keypad lock is Press the hash key R activated. Check cord routing (page 2). Authorisation This device is intended for analogue phone lines in your network. [. . . ]