User manual SCOTT TX 700 M TECHNICAL SPECIFICATIONS

[. . . ] Scott does not see frame, rear shock and kinematics as single components which are assembled together on a bike, but as a concept with all these components working together and offering an outrageous function by matching perfectly. The Gambler Concept is based on a new designed multi-pivot technology. In combination with the linear coil-over shock characteristics the kinematics guarantees a progressive suspension, adapted to smooth riding (beginning of travel) as well as extreme jumps (end of travel). GEOMETRY DATA TX 700 M TX 700 M A Size Head angle ° B Head tube length C Reach D Stack E BB center to top of seattube F Chainstay length G BB offset H BB height I Standover height Wheel base Stem length mm mm inches mm inches mm inches mm inches mm inches mm inches mm inches mm inches mm inches TX 700 M FR long 66. 0° 115 4. 5 410 165. 1 586 23. 1 424 16. 7 430 16. 9 25 1. 0 370 14. 6 790 31. 1 1170 46. 1 40 TX 700 M DH short long 64. 0° 64. 0° 115 115 4. 5 4. 5 375 14. 7 586 586 23. 1 23. 1 424 16. 7 424 16. 7 440 17. 3 440 17. 3 25 25 1. 0 1. 0 370 14. 6 370 14. 6 790 790 31. 1 31. 1 1135 44. 7 1170 46. 1 50 50 410 165. 1 4 2011 SCOTT BIKE OWNERS MANUAL 5 ENGLISH short 66. 0° 115 4. 5 375 14. 7 586 23. 1 424 16. 7 430 16. 9 25 1. 0 370 14. 6 790 31. 1 1135 44. 7 40 TX 700 M TECHNICAL DATA TX 700 M Travel Suspension Ratio Piston stroke TX 700 M Hardware Mainframe Hardware Swingarm Seatpost diameter Headset Fork travel Fork length BB housing Chainguide system Rear Hub Width Bearings 190 / 210 / 230mm 2. 5 / 2. 75 / 3. 0 76mm 22, 2mm x 8mm 40mm x 8mm 34, 9mm 1 1/8" or 1. 5", depending on headtube insert 180 - 200mm 568mm 83mm ISCG / ISCG05 tab 150mm 2 x 61901 (24 x 12 x T6) 6 x 61902 (28 x 15 x T7) ADJUSTMENT OF HEAD ANGLE On Gambler you can adjust the headangle within a few minutes for a better handling depending on your riding style and track condition/style. Howtoadjusttheheadangle: You need - a 56mm wrench (attached to this bike) 1. [. . . ] Please note that it is not necessary to disassemble the fork or any other components. Turn the insert with the 56mm wrench which is attached to your bike/frameset. The slot of the insert should always be in line with the slot of the headtube clamp. TX 700 M 7 ENGLISH Shock length (Eye to Eye) 241mm - a 4mm Allen key bit for a tighening torque key 3. IMPORTANT: Please make sure that there is no gap between the collar on the downside of the insert and the head tube clamp on the frame. 4. tighten the 3 screws with 5Nm/44in-lbs 6 2011 SCOTT BIKE OWNERS MANUAL 2 DIFFERENT HEADTUBE INSERTS On Gambler you have 2 options for the headset diameter (1 1/8" and 1. 5"). You can order the headtube inserts via your local Scott dealer with: 210127 TX 700 M Headtube Insert Gambler 1 1/8" 1. 5" 1size 1size 210128 Headtube Insert Gambler 3 DIFFERENT REAR TRAVEL OPTIONS On Gambler you have 3 options for the rear travel as shown on the drawing below: For removing/assemblying them please contact your local Scott dealer as you might need some special tools for the headset dis-/assembly as well as a tightening torque key to fix the inserts in the headtube section. Important: Itisveryimportanttofollowthetighteningtorqueindicationsshownontheparts. TX 700 M RECOMMENDED TOOLS FOR THE SET-UP Please read this manual and the manual of the rear shock manufacturer carefully before you start the set-up procedure. In addition we strongly recommend using a tightening torque key with a 6mm allen key insert. 8 2011 SCOTT BIKE OWNERS MANUAL 9 ENGLISH SET-UP TX 700 M The Set-Up of the rear shock can be easy done within a few minutes. Please take this time to avoid dangerous riding performance and to get the best out of your Gambler. TX 700 M NOTES PIVOT MAINTENANCE The pivots and bearings on SCOTT Gambler are extremely easy to maintain. An external treatment with a grease spray after every bike wash is all you have to do. We do not recommend heavy grease sprays since these will leave a film on the parts which is difficult to remove. If you have to change the bearings you can order them included in a service kit (Scott article number: 210126) at your local SCOTT dealer or buy them with international parts number as shown above in the specs list in a hardware store. Incaseofachangeofthebearingsoroftherearswingarmyoushouldcontactyour localSCOTTdealerasyouneedaspecialtoolkitfordisassemblyandassembly. ENGLISH 14 2011 SCOTT BIKE OWNERS MANUAL 15 TX 700 M WARRANTY WARRANTY SCOTT bikes are made using the most innovative production and quality methods. Doing so SCOTT warrants its frames and swingarms for five years (subject to compliance with maintenance ranges, see below) and SCOTT forks (provided it is a fork of SCOTT) for two years for defects in material and/or workmanship in case of purchase of completely assembled bikes. This warranty of 5 years for the frames shall only be granted in case once a year a maintenance service has been effected according to maintenance requirements as set forth in this manual by an authorised SCOTT dealer. The authorised SCOTT dealer shall confirm the effected annual maintenance service by stamp and signature. In case such an annual maintenance service has not been effected the warranty of 5 years for the frame shall be reduced to 3 years. Costs for maintenance and service have to be born by the owner of the SCOTT bike. [. . . ] On Gambler, Voltage Fr and Volt-X the warranty period is limited to 2 years. This warranty is limited to the first buyer, what means the first person who uses the bike and only with the use it was made for. Furthermore, this warranty is limited to purchases via authorized SCOTT-dealers The warranty is solely granted in case of purchase of a completely assembled bike to the explicit exclusion of purchases of not completely assembled bikes. ENGLISH Model TX 700 M Size Frame Date of purchase In case of a warranty claim the decision to repair or to replace the defective part is up to SCOTT. Non defective parts will only be replaced at the guarantee's own expense. [. . . ]