User manual RUSSOUND UNO-S1

[. . . ] Party (Party Mode) - Master or Off When in "PARTY MODE" the system is primarily controlled by a "MASTER" Keypad. Party Mode links all rooms to the same source which is selected by the Master Keypad room. Any keypad in the system can become a Master Keypad (if enabled) but only one Master Keypad may exist at a time in Party Mode. Selecting Master Keypad mode from another keypad will transfer Master Keypad control to that room and release it from the first. [. . . ] Damage to or destruction of components due to application of excessive power voids the warranty on those parts. In these cases, repairs will be made on the basis or the retail value of the parts and labor. To return for repairs, the unit must be shipped to Russound at the owner's expense, along with a note explaining the nature of service required. Be sure to pack the unit in a corrugated container with at least three (3) inches of resilient material to protect the unit from damage in transit. Before returning a unit for repair, call Russound at (603) 659-5170 for a Return Authorization number. Write this number on the shipping label and ship to: Russound, ATTN: Service, 5 Forbes Road, Newmarket, NH 03857 Due to continual efforts to improve product quality as new technology and techniques become available, Russound/FMP, Inc. reserves the right to revise system specifications without notice. UNO-S1 Keypad-Front Panel System On Indicator When the room is off, but the system is on in another room, is illuminated by a green backlight and the "SYS ON" icon remains visible. Src 3 1 Source Select Button scrolls through the six source inputs and the Aux* source. As the sources are sequentially selected, each source's name appears on the keypad LCD panel. When a source is selected in more than one room, the "SHARED" icon will appear on all UNO Keypads using that source. is also used to enter the User Menu with a press and hold action. 2 3 4 6 Volume Up/Down Buttons The room's audio output is adjusted using . 5 Command Keys The command keys allow control of the selected source at the UNO Keypad. The command keys are activated with a press and release, or press and hold to access secondary functions. 1 LCD PANEL - 5-character backlit display shows source, volume and room status (messages scroll twice, then display first 5 characters of message) SOURCE SELECT - Scrolls through the available sources. Press and hold brings up the USER MENU for Loudness, Bass, Treble, etc. VOLUME UP/DOWN - Raises and lowers the volume for the room IR RECEIVER - Receives IR signals and passes them to the controller and source equipment. POWER - Turns room ON or OFF when pressed once, press and hold a second time will turn on or off all rooms COMMAND KEYS - Pressing the command keys controls the source equipment UNO-S1 User Menu The User Menu allows the user to adjust the audio properties and control functions of a particular room. To enter or exit the User Menu, press and hold during normal operation. The following keys are used to navigate and make changes while using the User Menu: Press and release to adjust feature setting (increment) Press and release to adjust feature setting (decrement) Go to next feature Go to previous feature Select or view current feature setting 2 3 All trademarks are property of their respective owners. 4 5 5 Forbes Road, Newmarket, NH 03857 tel 603. 659. 5170 · fax 603. 659. 5388 e-mail: tech@russound. com www. russound. com 28-1174 Rev. 1 11/17/05 6 UNO-S1 Side Panel The UNO-S1's setup button and OS update pins are located on the right side of the keypad (when facing front). 1 OS Update/Run Jumper -The pins are jumpered when performing an OS update on the keypad (typically needed only on a keypad that has never been updated), and removed during normal operation. 2 Setup Button - Activates information and update menus for the keypad. 3 OS Update Port - Used to update the UNO-S1 keypad operating system firmware. If an update is released, it will be available online through the Document Center on www. russound. com. Look for it in the "Firmware and Downloads" section under Multi-Zone product type. [. . . ] For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings, or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings. Heat - The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat. Power Sources - The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. 10. Grounding or Polarization - Precaution should be taken so that the grounding or polarization means of an appliance is not defeated. GND UNO-S1 Front View Src 3 1 CAT-5 to UNO-S1 Connection COM B GND CAT-5 Cable Src 3 11. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through the openings. [. . . ]