User manual RUSSOUND ST2S

[. . . ] ST2S Smart Tuner Installation Manual IMPORTANT SAFEGUARDS 11. Grounding or Polarization - Precaution should be taken so that the grounding or polarization means of an appliance is not defeated. 12. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, receptacles, and the point where they exit from the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 13. Cleaning - The appliance should be cleaned only as recommended by the manufacturer. 14. Non-use Periods - The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time. [. . . ] # Channel Number and Name (#:CH NAME:) This selection displays the channel number and name (e. g. , 43:BackSpin, 121:ESPNews). ST2S Display Preference Mode Next Display Preference MEM TUNE ST2-RC OK ST2-KP UNO-S2 UNO-LRC1 Mode Band MEM MEM TUNE MEM Previous Display Preference 4 SIRIUS ID Mode (4. SIRIUS ID) This mode allows access to the SIRIUS Identification number for the SIRIUS module. This 12-digit number must be provided to SIRIUS during the activation procedure (Example: 123456789012) ST2S SIRIUS ID Mode SIRIUS ID Number Exit Current Mode Mode Band ST2-RC ST2-KP UNO-S2 UNO-LRC1 OK ST/ MONO 19 ST2S OPERATION SIRIUS RADIO MODES 5 Channel Lock Mode (5. CHAN LOCK) This mode allows you to lock/unlock a channel or channels to prevent audio access. This parental control is set/cleared with a four-digit code entered using the UNO-LRC1 or ST2-RC remote controls. Channel to be locked/unlocked must be selected before beginning this procedure. ST2S Channel Lock Mode Next Info Item Previous Info Item Mode Band ST2-RC OK ST2-KP UNO-S2 UNO-LRC1 MEM TUNE MEM MEM TUNE MEM L Lock Channel (LOCK CHAN:) This selection appears when an unlocked channel is selected. Using the UNO-LRC1 or ST2-RC remote control, enter the current four-digit code (default is 0000). The channel is now locked and will not appear when scrolling through channels. If the channel is selected numerically from the remote control, the user must enter the code to unlock access. U Unlock Channel (UNLOCK CHAN:) This selection appears when a locked channel is selected To UNLOCK a channel: 1. This temporarily unlocks the channel; when the channel is exited, it will lock again. C Change Code (CHANGE CODE:) This selection allows you to enter a new four-digit code for locking/unlocking channels. Press ENTER CODE appears. Mode Band on the ST2S, OK on the ST2-RC or on the UNO-LRC1. 2. SAVED appears and the ST2S returns to normal mode. 20 ST2S OPERATION FRONT PANEL CONTROLS Front Panel Operation Turning the unit on To turn the unit on, push the On/Off button up on the front panel. In cities, antennas can pick up multipath signals when they bounce off buildings and get doubled. The Local mode limits the noise associated with these reflected signals. Selecting the desired tuner From the front panel, use to toggle between SIRIUS and AM/FM. A backlight shows behind the selected label SIRIUS (green) or AM/FM (amber) to indicate the active tuner. In addition, the LCD panel is also backlit green for Tuner 1 and amber for Tuner 2. Each time a tuner is selected the display will refresh with the current station or preset, and all subsequent memory preset entries will be associated with that selected tuner. Bank/Memory Presets Each tuner has six banks of preset memory settings, and each bank holds six presets for a total of 36 possible presets for each tuner (72 total presets). Presets are associated with the tuner that is selected at the time the preset is saved. Memory Preset programming From the front panel, perform these steps: 1. Use . Selecting the desired band (AM/FM only) Push Mode Band to choose from one of six banks (1-6). 2 Mode Band to switch between AM and FM reception. to select an SIRIUS operating mode. Selecting a mode (SIRIUS) Push Mode Band . Exiting a mode (SIRIUS) Push to exit the SIRIUS mode selection menu. Signal Strength mode (SIRIUS) Press and hold and release. [. . . ] Use + and - buttons to select the source number to which Tuner 1 (SIRIUS) is connected. Use + and - buttons to select the name for the source (e. g. , Tuner 1 or SIRIUS). Press the Setup button three times to back out of the Installation Menu. Source Configuration Note: When the ST2S Tuner is used with the CAV6. 6 or other RNET controller, it is configured as an RNET command type "Peripheral" and is connected via the RNET bus. This makes the tuner behave as a fully integrated device with UNO-S2 keypad support. [. . . ]