User manual RUSSOUND ST2

[. . . ] ST2 Smart Tuner Dual AM/FM Tuner Installation Manual IMPORTANT SAFEGUARDS 11. Grounding or Polarization - Precaution should be taken so that the grounding or polarization means of an appliance is not defeated. 12. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, receptacles, and the point where they exit from the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 13. Cleaning - The appliance should be cleaned only as recommended by the manufacturer. 14. Non-use Periods - The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time. [. . . ] Push the desired memory preset (M1 through M6) button for more than 2 seconds. When the memory preset is saved, the appropriate preset number (M1 through M6) and SAVED appears on the LCD. The selected station setting reappears after the button is released. Recalling a Memory Preset To recall a memory preset, use to select the desired bank, then press the desired preset button (M1 to M6). In addition to direct selection, the memory presets can be accessed by using and scroll through all presets for the bank selected. to Selecting the desired band Push to switch between AM and FM reception. Selecting the desired frequency Press and release and for manual tuning. Selecting Stereo or Mono Output Press and release to toggle between stereo and mono mode. STEREO or MONO appears briefly on the screen when selecting mode. Backup and Restore Once all of the tuner settings are completed, it may be advisable to create a backup of the programmed settings for future use. The backup will then be available in case tuner settings need to be restored. The "RNET Backup Utility" is available through the Document Center at www. russound. com. Also required are a DB9 male-to-female cable and laptop or desktop PC. Selecting Distant or Local Reception Press and hold to toggle between distant and local mode. In cities, antennas can pick up multipath signals when they bounce off buildings and get doubled. The Local mode limits the noise associated with these reflected signals. Bank/Memory Presets Each tuner has six banks of preset memory settings, and each bank holds six presets for a total of 36 possible presets for each tuner (72 total presets). Presets are associated with the tuner that is selected at the time the preset is saved. 14 ST2 OPERATION ST2-RC REMOTE CONTROL ST2-RC Remote Control Operation Turning the unit on To take the ST2 tuner out of standby mode, push or any other button except TUNER 1 or TUNER 2. PWR Selecting Stereo or Mono Output Press to toggle between stereo and mono mode. On a preset, the stereo/mono setting is saved for that preset. ST/ MONO Selecting the desired tuner (Note: To change the tuner that is audio-active, you must have some other system control in place to change the source) To control a tuner, push or . When pressed, these buttons will be backlit green for Tuner 1 and amber for Tuner 2. After a tuner is selected, the next button press refreshes the display with the current station or preset for that tuner, and all subsequent button presses and memory preset entries will be associated with that selected tuner. TUNER 1 TUNER 2 Selecting Distant or Local Reception Press to toggle between Distant and Local mode. Normal operation is in Distant mode. LOC/ DX Recalling a Memory Preset To recall a memory preset, select the desired tuner, press MEM BANK to select the desired bank, then press Selecting the desired band Push AM/FM and enter the desired preset number (1 to 6). The memory presets can also be accessed by using MEM to switch between AM and FM reception. Selecting the desired frequency TUNE and to scroll through all presets for the selected bank. MEM Use and for manual tuning. To move quickly through the stations, press and hold either of the Tune buttons for more than 1. 5 seconds. TUNE Saving Favorites The remote control stores two "favorites" (similar to memory presets) per tuner. These are set simply by selecting either Tuner 1 or Tuner 2, setting the desired frequency and pressing and holding FAV 2 FAV 1 To directly select a station, press , and enter the three- or four-digit station frequency (1071 for 107. 1, etc. ). European regions use five-digit station frequencies. TUNE or until "FAV1 (2) saved" appears on the tuner. Stored Favorites are then recalled by pressing either FAV 1 Frequency Seek The SEEK function is performed by pressing and releasing to seek lower frequencies or for higher frequencies. SEEK tuning begins at the current frequency, seeks upward and stops at the next tuned station. [. . . ] Enter the Source Setup Menu by pressing the Play button on the UNO-S2 keypad. Use + and - buttons to select the source number to which Tuner 1 is connected. Use + and - buttons to select the name for the source (e. g. , Tuner 1). Press the Setup button three times to back out of the Installation Menu. Source Configuration Note: When the ST2 Tuner is used with the CAV6. 6 or other RNET controller, it is configured as an RNET command type PERIPHERAL and is connected via the RNET bus. [. . . ]