User manual RUSSOUND R850MC

[. . . ] If water or any other liquid enters the amplifier cabinet, take the amplifier to qualified service personnel for inspection. Cleaning - The appliance should be cleaned only as recommended by the manufacturer. From time to time you should wipe off the front and side panels and the cabinet with a soft cloth. Do not use rough material, thinners, alcohol or other chemical solvents or cloths since this may damage the finish or remove the panel lettering. [. . . ] Do not expose the amplifier to direct sun light or heating units as the amplifier internal components' temperature may rise and shorten the life of the components. 18. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through the openings. 19. Servicing - The user should not attempt to service the appliance beyond that described in the operating instructions. All other servicing should be referred to qualified service personnel. 20. Damage Requiring Service - The appliance should be serviced by qualified service personnel when: A. Objects have fallen, or liquid has been spilled into the appliance; or C. The appliance has been dropped or the enclosure is damaged. 2 R850MC AMPLIFIER INTRODUCTION The Russound R850MC is an 8-channel power amplifier and is ideal for use as the main amplifier in home theater and distributed audio systems. The eight channels are arranged in pairs to provide amplification for four stereo zones. The R850MC provides an array of useful features such as bridge mode operation, independent zone triggering, bus inputs and multiple speaker outputs per zone to meet a wide variety of applications and configurations. The R850MC is rated at 50 watts per channel into 8 ohms and 80 watts per channel into 4 ohms. With the Stereo/Bridged mono switch in the Bridged Mono position, both channels in the zone are combined for a higher powered mono output. In bridged mode, the R850MC is rated at 140 watts of power into a single 8 ohm load. Each amplifier output channel incorporates robust protection circuitry for safety and reliability under extreme circumstances. FRONT PANEL 1 R USSOUND R850MC POWER AMPLIFIER 1 Zone Indicator LEDs: The four LEDs correspond to the four stereo zone amplifiers. The LED will illuminate red when the amplifier power is on and the zone is in standby. The LED will illuminate green when the zone is active. RACK MOUNTING The R850MC amplifier can be rack mounted using the included rack-mount ears and hardware to attach the ears to the amplifier. The amplifier will take 3 rack spaces with the feet removed. R850MC Side View Rack Ear Screw Holes + + Rack Ear Front View Rack Ear Side View 3 R850MC AMPLIFIER 1 2 3 4 5 1 6 7 11 1 10 4 7 9 8 Bus Input/Output: The bus line input is an optional input that can be used to connect a single source to multiple zones. The bus line output is a passive passthrough of the bus input and can be used to daisy chain the source to other amplifiers in the system. Line Input: The line audio input for each zone is a dedicated sensing input that will activate the zone when an audio signal from a source is present. Line/Bus Switch: Sets the zone input to the Line Input or the Bus Input. Fuse Receptacle: Holds a replaceable fuse for AC power input connection. Fuse rating for North America is T10AL 250V and for Europe is T7AL 250V. AC Input: The AC voltage input for the North American model is 120VAC at 60Hz (European model, 230VAC at 50Hz). 12VDC Trigger In/Out: The 12V Trigger In is used to activate the zone. [. . . ] Thermal protection mode can only engage when the unit has been run at high volume for extended periods of time without adequate ventilation and/or when speaker impedances are below the minimum levels for the amplifier. If this fault occurs, turn off the amplifier, and check that the speaker impedance rating is above the minimum rating. Also check for adequate ventilation around the amplifier and make adjustments if necessary. Once the unit has cooled to safe operating temperatures, the amplifier may be powered back on. PROTECTION CIRCUITRY All Russound amplifiers are designed with special circuitry to safeguard the amplifier under a short-circuit condition. [. . . ]