User manual RUSSOUND R235LS

[. . . ] If water or any other liquid enters the amplifier cabinet, take the amplifier to qualified service personnel for inspection. Cleaning - The appliance should be cleaned only as recommended by the manufacturer. From time to time you should wipe off the front and side panels and the cabinet with a soft cloth. Do not use rough material, thinners, alcohol or other chemical solvents or cloths since this may damage the finish or remove the panel lettering. [. . . ] 16. Wall or Ceiling Mounting - The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer. 17. Location of the Amplifier - Do not mount this unit under a kitchen cabinet. Do not expose the amplifier to direct sun light or heating units as the amplifier internal components' temperature may rise and shorten the life of the components. 18. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through the openings. 19. Servicing - The user should not attempt to service the appliance beyond that described in the operating instructions. All other servicing should be referred to qualified service personnel. 20. Damage Requiring Service - The appliance should be serviced by qualified service personnel when: A. Objects have fallen, or liquid has been spilled into the appliance; or C. The appliance has been dropped or the enclosure is damaged. 2 R235LS AMPLIFIER INTRODUCTION The Russound R235LS is a 2-channel power amplifier with automatic local source switching capability. The R235LS allows a local source (e. g. , PC or TV in the bedroom) to automatically override the speakers in that particular zone of a distributed audio system. This can be accomplished with a variety of input/trigger options for versatility in many different applications. The R235LS is rated at 35 watts per channel into 8 ohms and 50 watts per channel into 4 ohms. With the Stereo/Bridge Mono switch in the Bridge Mono position, both amplifier channels are combined for a higher powered mono output. In bridged mode the R235LS is rated at 100 watts of power into a single 8-ohm load. Each amplifier output channel incorporates robust protection circuitry for safety and reliability under extreme circumstances. FRONT PANEL 1 2 On Off R USSOUND R235LS POWER AMPLIFIER 1 Power LED: The LED will illuminate red when the power is on and the amplifier is in Default/standby mode and illuminate green when the amplifier is active. 2 Power Switch: Turns the amplifier on/off. This switch does not disconnect the main power feed from the amplifier; this requires that the power cord be unplugged from the outlet. 3 R235LS AMPLIFIER 1 2 3 4 5 6 7 8 10 1 9 6 7 Line Input: The line audio input is a sensing input that will activate the amplifier when an audio signal from a source is present. Gain Controls: Left and Right gain controls independently adjust the sound level for each channel. Delay Time: The delay can be adjusted from about 5 seconds to 5 minutes. When an audio signal is not present, this delay setting will automatically switch the amp to the Default input mode after the preset period of time. 12VDC Trigger In/Out: The 12V Trigger In controls the amplifier switching from the default input (distributed audio system) to a local source. The delay and audio sensing are bypassed when the 12V trigger input is used. Default Input: The default input is a speaker-level passthrough from the default input to the speaker output. Speaker A/B Outputs: The A and B speaker outputs are in parallel to the amplifier output. [. . . ] The front panel LED illuminates orange when the amplifier is in short circuit protection. If this fault condition occurs, turn off the amplifier and check speakers for short circuit conditions when appropriate. 5 R235LS AMPLIFIER POSSIBLE SYSTEM CONFIGURATION The R235LS can be used as a single-source two-channel zone amplifier, or as a local-source amplifier that automatically switches between a default source (e. g. , a whole-house audio distribution system) and a local source (e. g. , a television set in the bedroom or a PC in the office). Line Outputs Video Right Left Amplified output to room speakers A/V RCA Cables Speaker Cable Optional video sensing Amplified input from audio distribution system R235LS Amplifier 6 R235LS AMPLIFIER SPECIFICATIONS Stereo Continuous Output Power: Bridged Output Power: THD+N: Signal-to-Noise Ratio: Frequency Response: Input Sensitivity: Input Impedance: Voltage Gain: Delay Time: Input Trigger: Output Trigger: Power Requirements: 35W per channel at 8 ohms 50W per channel at 4 ohms 100W at 8 ohms, 2 channels bridged 0. 05% from 20Hz to 20kHz >100dB A-weighted 20Hz to 20KHz +/- 0. 3dB 70mV for 1W at 8 ohms 420mV for 35W at 8 ohms 47kohms Line Input 32dB 5 seconds to 5 minutes 12VDC 10kohms 12VDC 100mA max North American Model: 120VAC 60Hz 1. 2A IEC 320 type connector with 3 terminal detachable power cord. European Model: 230VAC 50Hz 0. 6A IEC 320 type connector with 3 terminal detachable power cord. 8. 625" W x 10"D x 2. 375"H (22 x 25. 4 x 6 cm) 8. 5 lbs. (3. 8kg) Power Requirements: Dimensions: Weight: WARRANTY The Russound R235LS is fully guaranteed for two (2) years from the date of purchase against all defects in materials and workmanship. [. . . ]