User manual RUSSOUND KP4-KP6

[. . . ] To enter the User Options Mode, press and hold the Source button when the zone is on. To exit the mode, press and hold the Source button again (or wait for a 9-second timeout). The first four source buttons double as indicators for audio feature selection. When entering the User Options Mode, the top left (Source 1) button will temporarily blink to indicate "Bass" is ready for adjustment. [. . . ] reserves the right to revise system specifications without notice. AM/FM CABLE XM1 SERVER1 1 KP4 Keypad 2 8 Source 3 4 7 6 1 5 Button will blink to indicate the option that is ready for adjustment Source 1 Source 3 Source 2 Source 4 Source 6 SOURCE NAME - Clear window with replaceable source name labels. VOLUME UP - Raises the volume for the room and adjusts user option features. Press and hold brings up the USER MENU for Loudness, Bass, Treble, etc. VOLUME DOWN - Lowers the volume for the room and adjusts user option feature. IR RECEIVER - Receives IR signals and passes them to the controller and source equipment. Also used when the keypad is operated using the CA System remote controls. IR CONFIRMATION/LOUDNESS LED - Blue LED blinks to confirm IR signal reception, and remains lighted when Loudness feature is enabled. POWER - Turns room ON or OFF when pressed once; when OFF, press and hold to turn off all rooms; remains lit as system indicator. VOLUME LEVEL - Volume level indicator LEDs light up from left to right to indicate volume level. Also indicates user option adjustments. 2 Bass Balance Option setting level AM/FM CABLE XM1 SERVER1 Treble Turn On Volume Source 5 3 4 Press Volume Up or Down buttons to adjust setting Source Press and hold Source button to enter or exit User Options Mode Press Source button to select option 5 All trademarks are property of their respective owners. 6 7 5 Forbes Road, Newmarket, NH 03857 tel 603. 659. 5170 · fax 603. 659. 5388 e-mail: tech@russound. com www. russound. com 28-1201 07/29/05 Blue LED will blink to indicate Loudness is ready for adjustment 8 KP6/KP4 Side Panel The KP6/KP4 OS update jumper and KPSC 12-pin header are located on the right side of the keypad (when facing front). 1 OS UPDATE/RUN JUMPER -The pins are jumpered only when performing an OS update on the keypad, and removed during normal operation. KPSC PORT (KP6 only) - 12-pin header for connection to KPSC source control keypad. KP6/KP4 Back Panel The KP6/KP4 keypad uses a 110-punchdown terminal on the back panel to provide a simple installation and strong connection for CAT-5 cable's eight conductors. Attach the CAT-5 cable to the 110-punchdown terminal on the KP6/KP4 keypad as shown, matching the conductor colors to the connection color guide. The keypad will not operate properly if the terminations deviate from the required connection order. Take care when using an impact 110 punchdown tool, as this may overspread the contact points. Use of the impact tool may propel stray bits of wire and jacket into the keypad's chassis and possibly cause a short in the circuitry. Gently shake or blow air through the keypad chassis to remove stray wire before the keypad is installed into the junction box. KP6 Keypad to CA Controller Connection Each keypad connects to a Keypad Port on the back of the controller (CAA66 controller shown below). Connections are made using CAT-5 cable with an RJ45 connector (wiring scheme shown below). An SA-ZX3 Keypad Splitter can be used to add additional keypads to each zone. Safety Instructions 1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated. Retain Instructions - The safety and operating instructions should be retained for future reference. Heed Warnings - All warnings on the appliance in the operating instructions should be adhered to. [. . . ] Route CAT-5 wire to the junction box from the CA system controller. A. CABLE Objects have fallen, liquid has been spilled into the appliance; or The appliance has been exposed to rain; or The appliance does not appear to operate normally; or The appliance has been dropped or the enclosure is damaged. B. Use a 110 punchdown tool to connect each wire to its corresponding color labeled on the punchdown terminal. Mount the keypad in the electrical box, add the source name labels and attach the trim plate. 13. Servicing - The user should not attempt to service the appliance beyond that described in the operating instructions. All other servicing should be referred to qualified service personnel. Precautions: 1. [. . . ]