User manual RUSSOUND CAV66 1

[. . . ] CAV6. 6-S2 System 6-Zone, 6-Source Audio/Video Controller Amplifier INSTRUCTION MANUAL IMPORTANT SAFEGUARDS 9. Heat - The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat. 10. Power Sources - The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 11. Grounding or Polarization - Precaution should be taken so that the grounding or polarization means of an appliance is not defeated. [. . . ] PC computer running Windows 95, 98, ME, NT, 2000, XP operating system 2. Available DB9 serial RS-232 data port (baud rate= 38400, data bits = 8, no parity, 1 stop bit, no flow control) 3. Flash Magic - Philips IC update application (Flash Magic can be downloaded for free at: http://www. esacademy. com/software/flashmagic/flas hmagic. exe) Flash Magic Required Settings: Section 1: COM Port: = COM port connected to on PC Baud Rate: = 38400 Device: = XA-G49 Oscillator Freq. {MHz}: = 12. 288 Section 2: "Erase blocks 0-4" should be highlighted Note: Check "Erase all Flash + Security. " Also un-check "Set Security Bit 1-3" found in Sect. Section 3: Click "Browse" button to select the new . hex file to be used. Note: Make sure the proper hex file is selected (Main or AUX). Loading the wrong file will lock up the unit) Section 4: No boxes should be checked. Note: The same A/C power circuit should be used for the system and the PC. Remove the "Russound" program selector switch cover with a small flat blade screwdriver. Connect the DB9 serial cable between the PC COM port and one of the DB9 ports found on the front and rear panels of the CAV6. 6. Make sure the front/rear selector switch is in the corresponding position (front or rear). The hex file will be labeled AUX or Main; set the switch to match which file is being used. Section 5: Click the "Start" button to begin firmware update. The status is shown at the bottom of the window. Completion: Disconnect the Programming Cable from the controller and the PC. Re-position the OS Program selector switch to "Run. " Press and release the Reset button, or cycle main power off and on to the CAV6. 6. Note: Most updates will require both processors to be updated - the AUX should be updated first. Press and release the Reset button next to the OS Program selector switch, or cycle the power off and then on for the CAV6. 6. If error messages appear, they are typically generated due to communication problems. Verify all connections. 46 INSTALLER PC POWER TOOL OVERVIEW PC Power Tool Programming The PC Power Tool is a custom software program that provides an easy way to program the CAV6. 6 using a PC to upload the program settings to the controller via a serial cable. Available RS-232 serial port After PC Power Tool is installed on the computer, a new project is created in the program by following the screen prompts and selecting the appropriate source and zone settings. A "Project" refers to a complete controller setup, and is saved as a file on the PC. Once a project is ready, it must be uploaded to the CAV6. 6 from the PC. To upload the file, connect a DB9 serial cable between the PC COM port and either the front or rear DB9 connection on the CAV6. 6. The front/rear OS Program selector switch on the CAV6. 6 must be set as well (front or rear). With the PC Power Tool program selected to the desired project file, go to the "Tools" menu and select "Write to Device. " A status bar will move as the project file is uploaded from the PC to the controller. Disconnect the DB9 cable from the controller and cycle power to the controller. PC Power Tool project files can also be downloaded from the controller to be edited or to be uploaded to other controllers. PC Power Tool Start Screen PC Power Tool Project Upload Status Window 47 INSTALLER INITIAL INSTALL TEST Before proceeding to the system programming section, it's important to conduct an initial test to determine that the hardware components are working properly. [. . . ] The Home Theater left and right front main speaker outputs are connected to the input on the front of the SRM-2. 1. Zone 1 12V Trigger output is connected to the 12V +/- on the back of the SRM-2. 1. When zone 1 is powered on, the SRM-2. 1 is triggered allowing audio from zone 1 of the CAV6. 6 to power the speakers. When the UNO System Keypad for zone 1 is shut off, 12VDC is no longer provided to the SRM-2. 1, and the output of the SRM-2. 1 is switched to the Home Theater front left and right amplified speaker output. Components List: 1 - CAV6. 6 Controller 3 - UNO-S2 Keypads 1 - SRM-2. 1 Speaker Relay Module 1 - pair Advantage Iso-Mount Speakers 1 - 846C 12VDC Power Supply 3 - 845. 1 Micro Emitters 94 SAMPLE SYSTEM CONFIGURATION 6 Home Theater 95 INSTALLER KEY CODES TV (HDTV) KEY FUNCTION 1 2 3 4 5 6 7 8 9 0 Volume Up Volume Down Mute Channel Up Channel Dn Power Enter Prev Channel TV/Video TV/VCR A/B TV/DVD TV/LD Input TV/DSS Play Stop Search Fwd Search Rev 96 UNO-S1 TV (HDTV) 1 2 3 4 5 6 7 8 9 0 VolUp VolDn Mute Ch Up Ch Dn Power Enter PrvCh TVVid A/B TV LD Input Play Stop SrchF SrchR Digit 1 Digit 2 Digit 3 Digit 4 Digit 5 Digit 6 Digit 7 Digit 8 Digit 9 Digit 0 Volume Up Volume Down Mute Channel Up Channel Down Power On/Off Channel Enter Last Channel Learned Only Learned Only Learned Only TV/Video Learned Only Learned Only Learned Only Learned Only KEY FUNCTION UNO-S1 TV (HDTV) Pause Record Menu Menu Up Menu Dn Menu Left Menu Right Select Exit Display Guide Page Up Page Down Disk Plus 10 Open/Close Random Track Fwd Track Rev Sur On/Off Sur Mode Surround Up Surround Dn PIP PIP Move PIP Swap Program Sleep On Pause Recrd Menu MenuU MenuD MenuL MenuR Sel Exit Displ Guide PageU PageD Disk Pls10 Op/Cl Randm TkFwd TkRev SurOn SurMd SurUp SurDn PIP PIP M PIP S Progm Sleep On Learned Only Learned Only Menu (Picture) Menu Up, Adjust Up Menu Dn, Adjust Dn Menu Left Menu Right Menu Select Exit, Cancel Display, OSD, Info Guide Adjust up Adjust Down Learned Only +100 Learned Only Learned Only Learned Only Learned Only Surround On/Off Learned Only Learned Only Learned Only Learned Only PIP Move PIP Swap Learned Only Learned Only On, Power On/Off TVVCR Learned Only TVDVD Learned Only TVDSS Learned Only INSTALLER KEY CODES TV (HDTV) KEY FUNCTION UNO-S1 TV (HDTV) Off 11 12 13 14 15 16 Bright Dim Close Open Halt AM/FM Cue Disk Up Disk Down Info External Src Live/Intro Menu Back Fav Channel Display Fmt SAP Slow PIP On PIP Off PIP Freeze PIP Input Off 11 12 13 14 15 16 Brght Dim Close Open Halt Cue DiskU DiskD Info ExtSr Intro Menu Back FavCh DFrmt SAP Slow PIPOn PIPOf PIPFr PIPIn Off, Power On/Off Learned Only Learned Only Learned Only Learned Only Learned Only Learned Only Learned Only Learned Only Learned Only Learned Only Learned Only Learned Only Learned Only Learned Only Learned Only External Antenna Learned Only Menu (Audio) Back Favorite Fmt, Wide, 16:9, Aspct SAP, CC Learned Only PIP ON PIP OFF PIP Freeze PIP Input 97 KEY FUNCTION UNO-S1 TV (HDTV) PIP Chan Up PIP Chan Dn Input 1 Input 2 Input 3 Input 4 Input 5 Input 6 Input 7 Input 8 Input 9 Input 10 PIPCU PIPCD In 1 In 2 In 3 In 4 In 5 In 6 In 7 In 8 In 9 In 10 PIP Channel Up PIP Channel Down VID1, Video, TVp1 VID2, TVp2 VID3, TVp3 VID4, TVp4 VID5, AV1, VCR, BNC VID6, AV2, VDP, DVD, DVI TV, Component CAB, SAT, S-Video AV, Tuner AUX, RGB AM/FM Learned Only INSTALLER KEY CODES CABLE KEY FUNCTION 1 2 3 4 5 6 7 8 9 0 Volume Up Volume Down Mute Channel Up Channel Dn Power Enter Prev Channel TV/Video TV/VCR A/B TV/DVD TV/LD Input TV/DSS Play Stop Search Fwd Search Rev 98 UNO-S1 CABLE 1 2 3 4 5 6 7 8 9 0 VolUp VolDn Mute Ch Up Ch Dn Power Enter PrvCh TVVid TVVCR A/B TVDVD TV LD Input TVDSS Play Stop SrchF SrchR Digit 1 Digit 2 Digit 3 Digit 4 Digit 5 Digit 6 Digit 7 Digit 8 Digit 9 Digit 0 Volume Up Volume Down Mute Channel Up Channel Down Power On/Off Channel Enter Last Channel Learned Only Learned Only Learned Only Learned Only Learned Only Bypass, A/B Learned Only Play Stop Fast Forward Rewind KEY FUNCTION UNO-S1 CABLE Pause Record Menu Menu Up Menu Dn Menu Left Menu Right Select Exit Display Guide Page Up Page Down Disk Plus 10 Open/Close Random Track Fwd Track Rev Sur On/Off Sur Mode Surround Up Surround Dn PIP PIP Move PIP Swap Program Sleep On Pause Recrd Menu MenuU MenuD MenuL MenuR Sel Exit Displ Guide PageU PageD Disk Pls10 Op/Cl Randm TkFwd TkRev SurOn SurMd SurUp SurDn PIP PIP M PIP S Progm Sleep On Pause Record Menu, Settings Menu Up Menu Down Menu Left Menu Right Menu Select Exit, Cancel Info, Display, OSD Guide Page Up Page Down Learned Only +100 Learned Only Learned Only Quick Skip, Advance Instant Replay Day Down Learned Only Learned Only Learned Only Learned Only Learned Only Learned Only Learned Only Learned Only On, Power On/Off INSTALLER KEY CODES CABLE KEY FUNCTION UNO-S1 CABLE Off 11 12 13 14 15 16 Bright Dim Close Open Halt AM/FM Cue Disk Up Disk Down Info External Src Live/Intro Menu Back Fav Channel Display Fmt SAP Slow PIP On PIP Off PIP Freeze PIP Input Off 11 12 13 14 15 16 Brght Dim Close Open Halt Cue DiskU DiskD Info ExtSr Intro Menu Back FavCh DFrmt SAP Slow PIPOn PIPOf PIPFr PIPIn Off, Power On/Off Learned Only Learned Only Learned Only Learned Only Learned Only Learned Only Learned Only Learned Only Learned Only Learned Only Learned Only Learned Only Learned Only Learned Only Learned Only External AV Source Return to Live PPV (Wink) Back Favorite Help Day Up Learned Only Learned Only Learned Only Learned Only Learned Only 99 KEY FUNCTION UNO-S1 CABLE PIP Chan Up PIP Chan Dn Input 1 Input 2 Input 3 Input 4 Input 5 Input 6 Input 7 Input 8 Input 9 Input 10 PIPCU PIPCD In 1 In 2 In 3 In 4 In 5 In 6 In 7 In 8 In 9 In 10 Learned Only Learned Only A, VID1, Video, TVp1 B, VID2, TVp2 C, VID3, TVp3 VID4, TVp4 VID5, AV1, VCR, BNC VID6, AV2, VDP, DVD, DVI TV, Component CAB, SAT, S-Video AV, Tuner AUX, RGB AM/FM Learned Only INSTALLER KEY CODES VIDEO ACC KEY FUNCTION 1 2 3 4 5 6 7 8 9 0 Volume Up Volume Down Mute Channel Up Channel Dn Power Enter Prev Channel TV/Video TV/VCR A/B TV/DVD TV/LD Input TV/DSS Play Stop Search Fwd Search Rev 100 UNO-S1 VIDEO ACC 1 2 3 4 5 6 7 8 9 0 VolUp VolDn Mute Ch Up Ch Dn Power Enter PrvCh TVVid TVVCR A/B TVDVD TV LD Input TVDSS Play Stop SrchF SrchR Digit 1 Digit 2 Digit 3 Digit 4 Digit 5 Digit 6 Digit 7 Digit 8 Digit 9 Digit 0 Volume Up Volume Down Mute Channel Up Channel Down Power On/Off Channel Enter Last Channel Learned Only Learned Only Learned Only Learned Only Learned Only TV/Video, DTV Learned Only Play Stop Fast Forward Rewind KEY FUNCTION UNO-S1 VIDEO ACC Pause Record Menu Menu Up Menu Dn Menu Left Menu Right Select Exit Display Guide Page Up Page Down Disk Plus 10 Open/Close Random Track Fwd Track Rev Sur On/Off Sur Mode Surround Up Surround Dn PIP PIP Move PIP Swap Program Sleep On Pause Recrd Menu MenuU MenuD MenuL MenuR Sel Exit Displ Guide PageU PageD Disk Pls10 Op/Cl Randm TkFwd TkRev SurOn SurMd SurUp SurDn PIP PIP M PIP S Progm Sleep On Pause Record Menu, Home Menu Up Menu Dn Menu Left Menu right Menu Select Exit, Cancel, Go Info, Display, OSD Guide, View Page Up, Scroll Up Page Dn, Scroll Dn Learned Only +100. [. . . ]