User manual RUSSOUND CAM66T 1

[. . . ] CAM6. 6T-S1 System 6-Zone, 6-Source AM/FM Receiver and UNO-S1 Smart Keypads INSTRUCTION MANUAL IMPORTANT SAFEGUARDS 9. Heat - The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat. 10. Power Sources - The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 11. Grounding or Polarization - Precaution should be taken so that the grounding or polarization means of an appliance is not defeated. [. . . ] The connections for the trigger are made using a two-conductor cable with 1/8" male mini-plug jacks. This allows for the connection of an external paging or muting device. The CAM6. 6 can be programmed to mute audio for one or all zones as preferred when the 12VDC is applied. 12VDC Mute Trigger Out Mute Trigger Out 12VDC output is used for triggering an external amplifier, muting device or other paging component dependent on the Mute Trigger In 12VDC. The connections for the output are made using a two-conductor cable with 1/8" male mini-plug jacks at each end. The default setting for the Mute Trigger Out provides 12VDC whenever 12VDC is applied to the Mute Trigger In. CAM6. 6 Doorbell Interface 35 INSTALLER MAKING CONNECTIONS RNET Link In and Link Out The RNET Link In and Link Out can be used to connect two to six CAM6. 6 or CAV6. 6 controllers. The connection is made using a CAT-5 patch cable from the Link Out of the master CAM6. 6 and into the Link In of the next controller. Along with RNET data signals, the RNET Link In and Link Out jack passes the six source IR signals. These are only for source-specific IR remote repeating, not codes initiated from the controller's internal IR library. The CAT-5 patch cable should not exceed 18 inches in length to avoid potential cross-talk between the sourcespecific IR repeating signal lines. The RNET Link In and Link Out is also used to connect the CAM6. 6 to other Russound products with RNET. Note: If two or more CAM6. 6 or CAV6. 6 controllers will be connected using the RNET Link In and Link Out ports, each controller must have a unique Controller ID prior to being connected through the RNET ports. The Controller ID assignment must be performed during the Controller Setup section of the Installation menu. CAM6. 6 (Controller ID 1) CAT-5 Cable (MAX LENGTH 18 INCHES) CAM6. 6 CAV6. 6 (Controller ID 2) 36 INSTALLER MAKING CONNECTIONS RS-232 Interface The CAM6. 6 supports RS-232 communication with various third party automation systems or PC for programming of the controller. The RS232 com port is located on the back of the CAM6. 6 and uses a DB-9 cable connection. For RS-232 protocol and the backup PC application, see the Document Center at www. russound. com. Look for the Technical Documents under Multi-source/Multi-room products. CAM6. 6 INTERFACE DB9 Cable 37 INSTALLER MAKING CONNECTIONS Optional Internal Source - AM/FM Tuner Antennas AM Antenna Connect the included loop antenna for AM reception to the Optional Internal Source panel, attaching the GND (ground) and AM ends to the appropriately marked connections. FM Antenna Attach the included FM antenna for FM reception to the Optional Internal Source panel by pushing the F-type quick-connect termination of the antenna onto the FM connection. CAM6. 6 38 INSTALLER MAKING CONNECTIONS Optional Internal Source - AM/FM Tuner Antennas Connecting an Alternate Outdoor Antenna for AM/FM The diagram below depicts a suggested installation option of an alternate outdoor FM antenna and AM antenna. For best performance for AM reception, it is recommended to use an external outdoor or atticmounted long wire antenna for best performance for AM reception. Use a 75-ohm to 300-ohm balun at the AM connection on the tuner, and attach the 75-ohm coax cable to the balun. For best performance for FM reception, it is recommended to use an external outdoor or atticmounted antenna. Attach the desired length of 75-ohm coax cable directly to the FM connection on the tuner. 300 ohm to 75 ohm balun CAM6. 6 39 INSTALLER MAKING CONNECTIONS Grounding Outdoor Antennas Antenna Lead In Wire Electric Service Equipment Grounding Conductors Power Service Grounding Electrode System Ground Clamps Grounding an Outdoor Antenna If the tuner is used with an outdoor antenna, the antenna must be grounded against static charges and voltage surges. Consult the instructions that came with the antenna or contact the antenna manufacturer for proper installation instructions. The diagram above gives a general depiction of how an outdoor antenna should be grounded. For complete guidelines on antenna grounding procedures, please consult the National Electrical Code, Section 810, ANSI/NFPA No. [. . . ] Jazz Kids LD MSrvr MSvr1 MSvr2 MSvr3 MiniD Misc Mood MornM MP3 Oldes Pop RDoor Relig UNO-S2 DVD Player 3 Front Door Her Music His Music Intrnet Radio Jazz Kids Music Laser Disk Media Server Media Svr 1 Media Svr 2 Media Svr 3 Mini Disk Misc Lrnd IR Mood Music MorningMusic MP3 Oldies Pop Rear Door Religious 101 Dance DigCb DSS DSS 1 DSS 2 DSS 3 DVDCh DVDC1 DVDC2 DVDC3 DVD DVD 1 DVD 2 Dance Music Digitl Cable DSS Receiver DSS 1 DSS 2 DSS 3 DVD Changer DVD Changr1 DVD Changr2 DVD Changr3 DVD Player DVD Player 1 DVD Player 2 INSTALLER SOURCE NAMES UNO-S1 RepTV Rock Sat Sat 1 Sat 2 Sat 3 SatRd Src 1 Src 2 Src 3 Src 4 Src 5 Src 6 Src 7 Src 8 Spcl Tape Tape1 Tape2 TiVo Tuner 102 UNO-S2 ReplayTV Rock Satellite Satellite 1 Satellite 2 Satellite 3 Sat Radio Source 1 Source 2 Source 3 Source 4 Source 5 Source 6 Source 7 Source 8 Special Tape Tape 1 Tape 2 TIVO Tuner UNO-S1 Tun 1 Tun 2 Tun 3 TV VCR VCR 1 VCR 2 <XM> XM 1 XM 2 XM 3 XM UNO-S2 Tuner 1 Tuner 2 Tuner 3 TV VCR VCR 1 VCR 2 <<<XM>>> XM 1 XM 2 XM 3 XM Radio SAMPLE CONFIGURATIONS MULTIPLE CONTROLLERS WITH ONE TUNER Sharing a single CAM6. 6T (internal tuner) with multiple controllers This arrangement can support up to six CAM6. 6 units for up to 36 zones/6 sources. Each additional CAM6. 6 must have an incremental Controller ID # and RNET link. Audio from the source tuner can be split if shared by all controllers. CAM6. 6T Controller Setup Menu: Controller ID = 1 Peripheral Setup Menu: Controller ID = All Controllers Output/Input Switch = Internal Source Output RCA cable connected to Source 1 CAM6. 6 (no tuner installed) Controller Setup Menu: Controller ID = 2 Source Setup Menu: Basic Setup Procedure: Source # = 1; Source Name = Tuner; Command Type = Peripheral Output/Input Switch = Input RCA cable connected to Source 1 102. 5 102. 5 102. 5 UNO-S1 CAM6. 6 Back Panel (Controller ID 1) CAM6. 6 RCA Cables 102. 5 102. 5 102. 5 UNO-S1 CAM6. 6 Back Panel (Controller ID 2) CAM6. 6 103 SAMPLE CONFIGURATIONS MULTIPLE CONTROLLERS WITH TWO TUNERS System with two CAM6. 6T (internal tuner) controllers The configuration below is suitable for 7 to 12 zones that will have access to the tuner in the controller to which its keypad is connected only. If you have more than one internal tuner, you must set each tuner to its specific Controller ID number. [. . . ]